Dell Alienware m17 R2 Service Manual Download

Page: 64 / 70

Table 8. System setup options—Boot menu

Boot

Boot List Option

Displays the available boot options.
Default: UEFI

File Browser Add Boot Option

Enables you to add the boot options.

File Browser Del Boot Option

Enables you to delete the boot options

Secure Boot

Enable or disable the secure boot feature.
Default: Disabled

Legacy Option ROMs

Enable or disable the Legacy Option ROMs.
Default: Disabled

Attempt Legacy Boot

Enable or disable Attempt Legacy Boot.
Default: Disabled

Boot Option Priorities

Displays the boot sequence.

Boot Option #1

Displays the available first boot option.

Boot Option #2

Displays the available second boot option.

Boot Option #3

Displays the available third boot option.

Table 9. System setup options—Exit menu

Exit

Save Changes and Reset

Allows you to exit system setup and save your changes.

Discard Changes and Reset

Allows you to exit system setup and load previous values for

all system setup options.

Restore Defaults

Allows you to restore default values for all system setup

options.

Discard Changes

Allows you to load previous values for all system setup

options.

Save Changes

Allows you to save the changes for all system setup options.

Clearing CMOS settings

About this task

CAUTION: Clearing CMOS settings will reset the BIOS settings on your computer.

Steps
1. Remove the

base cover

2. Follow step 1 of removing the

coin-cell battery

to disconnect the coin-cell battery cable from the system board.

3. Wait for one minute.
4. Follow step 2 of installing the

coin-cell battery

to connect the coin-cell battery cable to the system board.

5. Replace the

back cover

Clearing BIOS (System Setup) and System passwords

About this task
To clear the system or BIOS passwords, contact Dell technical support as described at

www.dell.com/contactdell

Summary of Contents for Alienware m17 R2







































































Search results

Summary of Contents for Alienware m17 R2

Reviews:

Related manuals for Alienware m17 R2

Brands by name

Popular brands

Dell Alienware m17 R2, Service Manual

Search results

Summary of Contents for Alienware m17 R2

Reviews:

Related manuals for Alienware m17 R2

Brands by name

Popular brands