Dell Alienware m17 R2 Service Manual Download | Manualshive

Page: 24 / 70

background image

Steps
1. Peel and lift the Mylar covering the system board.
2. Disconnect and peel the Tron light cable from the system board and route the cable through the slot on the Mylar.

NOTE: To prevent damaging your computer ensure the Tron light cable has been disconnected from the system board
before removing the rear I/O-cover.

3. Remove the two screws (M2.5x5) that secure the rear I/O-cover to the palm-rest assembly.
4. Firmly grasp the sides of your computer with both hands and push the rubber feet on the rear I/O-cover outwards with your

thumbs to release the rear I/O-cover from the palm-rest assembly.

5. Lift the rear I/O-cover from the palm-rest assembly.

Installing the rear I/O-cover

Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.

About this task
The following image indicates the location of the rear I/O-cover and provides a visual representation of the installation procedure.

24

«
...
22
23
24
25
26
...
»

Summary of Contents for Alienware m17 R2







































































Reviews:

No comments

Related manuals for Alienware m17 R2

Brand: EVGA Pages: 15

Brand: EUROCOM Pages: 96

THINKPAD 92P1956

Brand: IBM Pages: 10

CELSIUS Mobile A

Brand: Fujitsu Siemens Computers Pages: 95

Atlas KAL14N300HA

Brand: Kogan Pages: 10

VAIO VGN-AR650U

Brand: Sony Pages: 2

VAIO VGN-A600B CTO

Brand: Sony Pages: 1

VAIO VGN-AR605E

Brand: Sony Pages: 2

VAIO VGN-AR610E

Brand: Sony Pages: 2

VAIO VGN-AR350E

Brand: Sony Pages: 2

VAIO VGN-AR230G

Brand: Sony Pages: 2

Brand: Sony Pages: 1

Brand: Sony Pages: 1

Brand: Sony Pages: 1

VAIO VGN-A140 Series

Brand: Sony Pages: 1

Brand: Sony Pages: 1

VAIO VGN-A600 Series

Brand: Sony Pages: 1

Brand: Sony Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands