manualshive.com logo in svg

Dell Alienware m15 R3, Service Manual, Page: 50 / 81

Share
Download
Dell Alienware m15 R3 Service Manual Download Page 50

Steps
1. Using the alignment posts, connect the left I/O-board connector board to the system-board assembly

NOTE: The I/O-board connector board is polarity sensitive. To prevent damaging your computer, utilize the alignment
pins to correctly replace the I/O-board connector board.

2. Using the alightment posts, replace and connect the left I/O-board to the connector on the system-board assembly.
3. Replace the four screws (M2x4.5) that secure the left I/O-board to the system-board assembly.

Next steps
1. Follow the procedure from step 3 to step 24 in 

Installing the system board

.

2. Install the 

right IO-board

.

3. Install the 

rear IO-cover

.

4. Install the 

M.2 2230 solid-state drive

. (if applicable)

5. Install the 

M.2 2280 solid-state drive

. (if applicable)

6. Install the 

M.2 2230 WWAN/solid-state drive

. (if applicable)

7. Install the 

battery

.

8. Install the 

base cover

.

9. Follow the procedure in 

After working inside your computer

.

Fan and heat-sink assembly

Removing the fan and heat-sink assembly

Prerequisites
1. Follow the procedure in 

Before working inside your computer

.

2. Remove the 

base cover

.

3. Remove the 

battery

.

4. Remove the 

M.2 2230 solid-state drive

. (if applicable)

5. Remove the 

M.2 2280 solid-state drive

. (if applicable)

6. Remove the 

rear IO-cover

.

7. Remove the 

right IO-board

.

8. Follow the procedure from step 1 to step 19 in 

Removing the system board

.

50

Summary of Contents for Alienware m15 R3


















































































Reviews:

No comments