Alignment & Adjustments
Service Manual
6-23
Display Meaning
Suggested
solutions
Memory Full
The memory is full.
Delete unnecessary documents,
Cancel or Start
retransmit after more memory becomes
available.
Memory Full
The memory is full.
Split the transmission into more than
Divide the Job
one operation.
No Answer Try Later
The remote fax machine has not answered Try again. Verify the number to make
after several redial attempts.
sure a fax can be received.
No Cartridge
The toner cartridge is not installed.
Install the toner cartridge. See
Load Cartridge
"Installing the Toner Cartridge".
No Paper
The paper in the paper tray has run out.
Load paper in the paper tray. See
Add Paper
"Loading Paper".
No such job
You are performing an Add/Cancel
Check the display to see if there are
operation, but there are no jobs waiting.
any scheduled jobs. The display should
indicate if any scheduled jobs are in
Standby mode, for example, Delay Fax.
Over Heat
There is a problem in the fuser unit.
Unplug the power cord and plug it back
Call Service
in. If the problem persists, call for service.
Open Heat Error Call
There is a problem in the fuser unit.
Unplug the power cord and plug it back
Service
in. If the problem persists, call for service.
Paper Jam 0
Paper has jammed in the feeding area
Clear the jam. See "Paper Feed Jam
Open Front Door
of the paper tray.
(tray 1)" or "Paper Feed Jam (optional
tray 2)".
Paper Jam 1
Paper has jammed in the fuser area.
Clear the jam. See "Fuser Area Jam".
Cartridge Area
Pager Jam 2
Paper has jammed in the paper exit area.
Clear the jam. See "Paper Exit Jam".
Open Rear Door
Power Failure
The power has been turned off and then
The printer's memory was not saved
Data Lost
on and the printer's memory has not been
due to a power failure. The job will
saved.
need to be started over.
Printer Error Cycle Power
A problem has occurred in the Laser
Unplug the power cord and plug it back
Scanning Unit (LSU).
in. If the problem persists, call for service.
Ready-toner 0%
The toner cartridge is empty.
Replace the toner cartridge with a new
TONER EMPTY
one. See "Replacing the Toner Cartridge".
Ready-toner 7%
The toner cartridge is almost empty.
Take out the toner cartridge and
TONER LOW
thoroughly shake it. By doing this, you
can temporarily reestablish printing
operations.
OR
Replace the toner cartridge with a new
one for the best print quality. See
"Replacing the Toner Cartridge".
Scanner locked
The scanner module is locked.
Unlock the scanner and press Start.
Unlock scanner
Self Diagnostic
The engin in your printer is checking
Please wait a few minutes.
some problems detected.
Waiting for redial
The machine is waiting for the
Please wait a few minutes.
programmed interval to automatically
redial.
Summary of Contents for 1815 Mono Laser
