Dell EMC Vblock Systems 350 Administration Manual Download Page 148

Page: 148 / 181

To run the backup, type:

UCS-A#

scope system

UCS-A /system* #

scope backup v00001vmfm01

UCS-A /system* #

enable

Password:

UCS-A /system* #

commit-buffer

UCS-A /system #

Creating and running the backup using scheduled backups

Create and run the FI backup using scheduled backups.

About this task

The following conditions apply for scheduled backups:

•

Scheduled backups can be configured for full state.

•

You cannot set the exact time of day that the scheduled backup occurs.

•

The full state backup is a binary file that includes a snapshot of the entire system.

—

Use the binary file to restore the system during disaster recovery.

—

Use the binary file to restore or rebuild the configuration on the original FI or recreate the
configuration on a different FI.

—

You cannot use the binary file for an import.

•

Full state backups are encrypted.

•

The full state backup policy can be configured to daily, weekly, or biweekly.

•

You cannot modify the maximum number of backup files created by the Cisco UCS Manager.

•

The option to configure scheduled backups can be found on the

Admin

tab and on the right side

of the screen on the

Policy Backup & Export

tab.

Procedure

To use the Cisco UCS Manager GUI to configure scheduled backups, refer to

Cisco UCS

Manager GUI Configuration Guide, Release 2.x, UCS Manager GUI Configuration Guide,
Release 3.x.

To use the Cisco UCS Manager CLI to configure scheduled backups, refer to

Cisco UCS

Manager CLI Configuration Guide, Release 2.x, UCS Manager GUI Configuration Guide, Release
3.x.

Guidelines for backing up configuration files

148

Summary of Contents for Vblock Systems 350






















































































































































































Search results

Summary of Contents for Vblock Systems 350

Reviews:

Related manuals for Vblock Systems 350

Brands by name

Popular brands

Dell EMC Vblock Systems 350, Administration Manual

Search results

Summary of Contents for Vblock Systems 350

Reviews:

Related manuals for Vblock Systems 350

Brands by name

Popular brands