Dell EMC Vblock Systems 350 Administration Manual Download Page 141 | Manualshive

Page: 141 / 181

background image

What to do next

Establish a procedure to restore a single configuration file, the entire repository, and the supporting
process to populate it, or restore the complete host where the repository exists.

Restoring a configuration file

Restore a network or storage device configuration file in the event of failure, corruption, or other data loss
event.

About this task

Follow the vendor recommended restore processes for the device.

Before you begin

•

Verify that local or remote connectivity exists to the impacted device.

•

Access the configuration file needed to restore operational status.

•

Obtain a method to transfer the configuration file from the source location to the impacted device
whether it be FTP, or copy and paste.

Procedure

To restore a configuration file, refer to the documentation provided with the vendor to restore the device.

Backing up targets in the Converged System

Back up targets that are in the AMP-2 in the Converged System.

About this task

•

Perform daily backups of all VMs at 7 A.M. and 7 P.M.

•

Perform daily backups of the VMware vCenter SQL Server database every four hours. This
coincides with server daily backups at 3, 7, 11 A.M. and 3, 7, 11 P.M.

•

Set the retention value to 35 days.

Disk storage resources should be monitored to prevent overuse issues and data
unavailability.

If AMP-2 is lost, the AMP-2 servers backup and binaries must be stored on the backup media to be
installed or restored otherwise you will be unable, or severely limited, in the ability to manage or recover
the Converged System. AMP-2 servers are:

•

VCSA Appliance

•

Platform services controllers

•

VMware vCenter Server, Web Server and Inventory Service

•

VMware vCenter SQL database

141

|

Managing AMP-2

«
...
139
140
141
142
143
...
»

Summary of Contents for Vblock Systems 350






















































































































































































Reviews:

No comments

Related manuals for Vblock Systems 350

Brand: Vacron Pages: 2

Brand: Yamaha Pages: 16

Brand: Yamaha Pages: 2

Brand: Yamaha Pages: 83

Brand: Yamaha Pages: 24

Brand: Yamaha Pages: 7

Brand: Yamaha Pages: 6

Brand: Yamaha Pages: 14

Brand: Yamaha Pages: 10

Brand: Yamaha Pages: 50

Brand: Yamaha Pages: 8

Brand: Q-Logic Pages: 3

Brand: Phase Technology Pages: 11

Brand: Air Liquide Pages: 16

Brand: Monacor Pages: 2

Brand: Garadise Pages: 3

MMA-300/2 PROFI

Brand: Zenit Powertools Pages: 10

Brand: Cairox Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands