background image

18 

30SD, 36SD, 45SD 

 

Rev. Nov2014 

Operating Instructions 

Using your DEK Snow Blower 

The following tips will help ensure proper and long lasting use of your DEK snow blower. ALWAYS wear proper  
safety equipment when operating the snow-blower, and make sure you dress appropriately for cold weather. 

Shear-Pins 

Collector 

Impeller 

Figure 1 

Figure 3 

Figure 4 

Discharge Angle 

Chute Direction 

Figure 2 

Figure 1 



Before use, always ensure there is nothing lodged in the collec-
tor, or impeller area. Inspect the auger and impeller for damage 
from rocks or other debris, and ensure there is no string, twine, 
etc stuck on the auger or impeller shafts. Visually inspect for 
loose hardware or any control cables that are loose or dis-
connected. Ensure the shear-pins are intact before operation. 



Inspect the area you will be operating the snow blower.  Avoid 
areas with rocks, large branches and limbs, or other debris that 
may damage the snow-blower. If operating the snow blower on 
a non-paved surface, lower the skid shoes to increase ground 
clearance, and prevent foreign objects from being thrown. 

Figure 2 



To prolong the life of the friction wheel system, do not partially 
engage the drive system, or continually engage and  
dis-engage the drive system if the engine begins to slow under 
heavy loads. When operating the snow-blower in dense wet 
snow, or deep snowfalls, select a slower forward speed.  Also, 
only shift speeds after coming to a complete stop. 

Figure 3 



The snow blower uses a solid axle which means the wheels on 
either side of the snow blower turn together. When turning the 
snow-blower, do NOT stop the collector/impeller assembly. 
Keep the transmission engaged and pull on the handlebars to 
shift weight to the outside tire while pushing the snow blower 
through the turn. This will assist in turning the snow blower, 
and is especially important for the 45SD which uses double 
tires on each side. 



Example: If turning left, shift the weight of the snow 
blower to the right. More weight on the right wheel 
helps the right side push the snow blower in the  
direction you wish to turn. 



The wheels slip better when spinning than when  
stationary. Keeping the transmission engaged aids in 
turning the snow blower. 



Keeping the collector /impeller assembly running  
prevents heavy snow from building up and making the 
unit difficult to turn. 

Figure 4 



Set the desired dis-charge direction and angle before engaging 
the auger/impeller.  Always be aware of your surroundings and 
the direction the discharge chute and deflector are throwing 
snow to avoid injury to by standers or property damage. 

Summary of Contents for 30SD










































Reviews: