background image

Form No. 3358-441 Rev

 

D

CCR

®

6053 Quick Clear™ Snowthrower

Model No. 38571—Serial No. 280000001 and Up

Model No. 38575—Serial No. 280000001 and Up

Operator's Manual

Introduction

Read this information carefully to learn how to operate
and maintain your product properly and to avoid injury
and product damage. You are responsible for operating
the product properly and safely.

You may contact Toro directly at www.Toro.com for
product and accessory information, help finding a
dealer, or to register your product.

Whenever you need service, genuine Toro parts, or
additional information, contact an Authorized Service
Dealer or Toro Customer Service and have the model
and serial numbers of your product ready. Figure 1
identifies the location of the model and serial numbers
on the product. Write the numbers in the space
provided.

Figure 1

1.

Model and serial number location

Model No.

Serial No.

This manual identifies potential hazards and has
safety messages identified by the safety alert symbol
(Figure 2), which signals a hazard that may cause serious
injury or death if you do not follow the recommended
precautions.

Figure 2

1.

Safety alert symbol

This manual uses 2 words to highlight information.

Important

calls attention to special mechanical

information and

Note

emphasizes general information

worthy of special attention.

Safety

This snowthrower meets or exceeds the ISO
standard 8437 in effect at the time of production.

Read and understand the contents of this manual
before the engine is ever started.

This is the safety alert symbol. It is used to alert

you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid
possible injury or death.

Improperly using or maintaining this snowthrower
could result in injury or death. To reduce this
potential, comply with the following safety
instructions.

Training

Read, understand, and follow all instructions on the
machine and in the manual(s) before operating this
unit. Be thoroughly familiar with the controls and
the proper use of the equipment. Know how to stop
the unit and disengage the controls quickly.

Never allow children to operate the equipment.
Never allow adults to operate the equipment without
proper instruction.

Keep the area of operation clear of all persons,
particularly small children.

Exercise caution to avoid slipping or falling.

© 2008—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420

Register at www.Toro.com.

Original Instructions (EN)

Printed in the USA

All Rights Reserved

Summary of Contents for CCR 6053 Quick Clear





















Reviews: