manualshive.com logo in svg

Degelman M28, Operator'S & Parts Manual

Share
Download
Degelman M28 Operator'S & Parts Manual Download Page 37

-35-

142657 - Manure Spreader     (17-March-2016)

246582 - Driveline Shaft, 1-3/4 x 45 (1)

Driveline Components

246736 -  Driveline Shaft, 1-3/4 x 135 (2)

117205 - Bearing, Assembly

Pillow Block, Wooden -1-3/4

      M28, Qty -  (7)
      M34, Qty -  (9)
       comes with...

117208 - Base (1)
117206 - Half Shell (2)

118514 - Flat Washer, 5/8 (2)

117494 - Bolt, Carriage, 

5/8 x 1-1/2 (2)

118508 - Lock Washer, 5/8 (2)
118407 - Nut, 5/8 (2)

117207 - Cap (1)

Driveline, CV/

Slider Shaft

Driveline, CV/

Slider Shaft

160310 - Driveline, 

Slider Shaft (1)

160310 - Driveline, 

Slider Shaft (1)

246736 -  Driveline Shaft, 1-3/4 x 135 (2)

246508 - Coupler, 

Assembly - Line Shaft, 

M28, Qty -  (1)
M34, Qty -  (2)

comes with...

246509 - Key, 

1/2 x 5-3/4 (1)

118087 - Bolt, 

3/8 x 2 (6)

118417 - Lock Nut, 3/8 x 2 (6)

118256 - 

Allen Setscrew 

5/8 x 5/8 (2)

118405 - Nut, 1/2 (4)

118504 - Lock Washer, 1/2 (4)

118512 - Flat Washer,1/2 (4)

246738 - Bracket, 

Bearing Holder (1)

118009 - Bolt, 1/2 

x 1-1/4 (4)

IMPORTANT:

 When installing, 

ensure tapered collar is locked 

onto shaft and not slipping

IMPORTANT:

 After nut is properly 

tightened, bend tab(s) of lock ring onto nut.

IMPORTANT:

 When attaching driveline onto shaft, tighten cut-out clutch 

bolt to to 75 ft-lbf (102 N·m). Check and retorque again after 2 hrs.

118447 - Lock Nut, 5/8 (2)

118537 - Flat 

Washer, 5/8 (4)

117220 - Bearing 

Assembly (1)

118026 - Bolt, 

5/8 x 2 (2)

M28 - Qty (2) / M34 - Qty (3)

117210 - Bearing 

Assembly (1)

DRIVELINE & MOUNTING COMPONENTS

Summary of Contents for M28














































Reviews:

No comments

Brands by name

Popular brands

Load more brands