manualshive.com logo in svg

Degelman M28, Operator'S & Parts Manual

Share
Download
Degelman M28 Operator'S & Parts Manual Download Page 20

-18-

142657 - Manure Spreader     (17-March-2016)

Service & Maintenance

 

IMPORTANT

:

 

Be sure to block up unit securely 

before removing tires.

DISASSEMBLY

1. Carefully pry off dust cap.
2. Remove cotter pin from nut.
3. Remove nut and washer.
4. Pull hub off spindle.
5. Dislodge the inner cone bearing and dust seal.
6. Inspect cups that are press fitted into hub for pits 

or corrosion and remove if necessary.

7. Inspect and replace defective parts with new 

ones.

WHEEL HUB REPAIR

ASSEMBLY

1. If cups need replacing, be careful to install 

them gently and evenly into hub until they are 

fully seated.

2. Apply a thick wall of grease inside hub. Pack 

grease in cones.

3. Install dust seal as illustrated, and inner cone.
4. Position hub onto spindle and fill surrounding 

cavity with grease.

5. Assemble outer cone, washer and nut.
6. Tighten nut while rotating hub until there is a 

slight drag.

7. Turn nut back approximately 1/4 turn to 

align cotter pin hole with notches on nut. 

Note:  Hub should rotate freely.  If not, repeat 

step 6.

8. Install cotter pin and bend legs sideways over 

nut.

9. Fill dust cap half full of grease and gently tap 

into position.

10. Pump grease into hub through grease fitting 

until lubricant can be seen from dust seal.

Spindle

Inner Cone

Inner Cup

Hub

Dust Seal

Outer Cone

Outer Cup

Cotter Pin

Slotted Nut

Washer

Dust Cap

COMMON SPINDLE AND HUB COMPONENTS

Summary of Contents for M28














































Reviews:

No comments

Brands by name

Popular brands

Load more brands