manualshive.com logo in svg

Degelman M28, Operator'S & Parts Manual

Share
Download
Degelman M28 Operator'S & Parts Manual Download Page 30

-28-

142657 - Manure Spreader     (17-March-2016)

118427 - Nut, 5/16 (4)

118405 - Nut, 1/2 (4)

118407 - Nut, 5/8 (4)

118000 - Nut, #10-24 UNC (4)

118420 - Lock Nut, 1/2 (4)

118047 - Bolt, 3/4 x 2-1/2 (2)

246511 - Clutch Guard 

Bracket (1)

118110 - Bolt, 5/16 x 1 (4)

118011 - Bolt, 1/2 x 1-1/2 (4)

118009 - Bolt, 1/2 x 1-1/4 (4)

118026 - Bolt, 5/8 x 2 (4)

118998 - Mach Screw, #10-24 

x  1/2”(4)

133094 - Nut, M8 x 1.25 (2)

129085 - Latch, 

Draw (2)

246456 - PTO Holder (1)

246404 - Shield Pin Assy

LH (shown) (1)

246403 - Shield Pin Assy

RH (opposite) (1)

246748 - Hose Holder, Assy (1)

246371 - Rubber Flap (1)
246370 - Bolt Bar (1)

118929 - Lock Pin, 3/8 x 1-1/2 (1)

160004 - Shield, Cone (1)

118530 - Lock Washer, 5/16 (4)

118504 - Lock Washer, 1/2 (4)

118508 - Lock Washer, 5/8 (4)

118999 - Lock Washer, #10 (4)

118509 - Lock Washer, 3/4 (2)

118731 - Flat Washer, 5/16 SAE (4)

117210 - Bearing Assy, Flange-2H (1)

118410 - Nut, 3/4 (2)

160352 - Driveline, Slider Shaft (1)

246409 - Front Shield, Assembly (1) 

comes with handle and latches...

118403 - Nut, 3/8 (13)
118503 - Lock washer, 3/8 (13)
118511 - Flat washer, 3/8 (13)

118136 - Bolt, 

3/8 x 1-1/2 (13)

5”

133093 - Capscrew, SH M8 x 1.25 x 30mm (2)

133092 - Handle (1)

Front Shield Components

FRONT SHIELD COMPONENTS

DRIVELINE SHIELD & BEARING COMPONENTS

IMPORTANT:

 

When installing, ensure 

tapered collar is locked onto 

shaft and is not slipping.

IMPORTANT:

 After nut is 

properly tightened, bend tab(s) 

of lock ring onto nut.

IMPORTANT:

 When attaching 

driveline onto shaft, tighten cut-out 

clutch bolt to to 75 ft-lbf (102 N·m). 

Check and retorque again after 2 hrs.

Optional: 

160374 - Driveline, 

Slider Shaft (1)

Summary of Contents for M28














































Reviews:

No comments

Brands by name

Popular brands

Load more brands