manualshive.com logo in svg

Degelman M28, Operator'S & Parts Manual

Share
Download
Degelman M28 Operator'S & Parts Manual Download Page 18

-16-

142657 - Manure Spreader     (17-March-2016)

Service & Maintenance

To remove and replace one or more chain slats, 

follow this procedure:

1. Fully loosen the chain tightener bolts on both 

side tightener and center support blocks to 

allow maximum slack in chain.

2. With slackened chain, skew/offset existing 

damaged chain slat to allow slat holder plates 

to be removed from the slat ends. 

3. Place end of new slat onto existing slat holder 

plate and skew/offset into position.

4. Repeat with remainder of damaged slats.
5. When finished replacing slats, fully re-tighten 

the side tightener blocks and firm up center 

support block against front conveyor axle.

6. Ensure front shield is closed.
7. Check chain tightness after operating and 

tighten as required.

REPLACING A DRAG CHAIN SLAT

Chain Slat

Chain Slat 

Holder Plate

Center Support 

Block

Front 

Shield

Chain 

Slat

Chain 

Tightener 

Bolt

Side Tightener 

Block

Front 

Conveyor 

Axle

ADJUSTING CHAIN TENSION

If drag chain has slack, tightening is required:
1. Loosen the jam nut. (Both sides of machine)
2. When tightening, hold middle nut with wrench 

and tighten rod end in a clockwise direction. 

3. a) Start on one side and tighten the threaded 

rod a few turns. 

  b) Repeat on opposite side of machine to evenly 

tighten chain tension. 

  c) Repeat this procedure 2-3 times until 

moderate chain tension is achieved. 

  d) After advancing the chain with this 

procedure, measure the distance from the 

round capscrew to the end of the slot. Compare 

this measurement with the opposite side 

measurement. Ensure the difference is less then 

1/2” MAX to prevent excessive skewing of 

chain slats.

4. Re-tighten jam nut securely against middle nut.
5. Repeat on other side.
6. Re-adjust center support on front conveyor axle.

1) Loosen

2) Hold

3) Tighten 

(clockwise)

DRAG CHAIN 

1. Occasionally check the Drag Chain for any bent 

or damaged slats. It is important to straighten or 

replace any damaged slats immediately.

2. The drag chain tension should be checked and 

adjusted on occasion. 

Summary of Contents for M28














































Reviews:

No comments

Brands by name

Popular brands

Load more brands