DeDietrich Innovens MCA 25/28 BIC Installation And Service Manual Download Page 30

Page: 30 / 124

Inserts

Ø4 wood screw

For the connection of the outside temperature sensor, refer to

the chapter "Electrical Connections".

4.10 Electrical connections

4.10.1.

Control unit

The boiler is fully pre-wired. The mains supply is made via the cable

connected to the mains. All other external connections can be made

to the connection connectors (low voltage). The main characteristics

of the control unit are described in the table below.

Power supply voltage

230 VAC/50Hz

Rating of the main fuse F1 (230 VAC) 6.3 AT
Fuse rating F2 (230 VAC)

2 AT

Fan-DC

27 VDC

CAUTION

Keep to the polarity shown on the terminals: phase (L),

neutral (N) and earth

CAUTION

The following components of the appliance are at a

voltage of 230 V:

Boiler pump (Heating circuit).

Boiler pump (DHW circuit).

Combined venturi and gas valve unit.

3-way valve.

The majority of components in the control panel and

the terminal box.

Power supply cable.

8800N003-C

4. Installation

MCA 25/28 BIC

15/06/12 - 300022159-001-01

Summary of Contents for Innovens MCA 25/28 BIC





























































































































Search results

Summary of Contents for Innovens MCA 25/28 BIC

Reviews:

Brands by name

Popular brands

DeDietrich Innovens MCA 25/28 BIC, Installation And Service Manual

Search results

Summary of Contents for Innovens MCA 25/28 BIC

Reviews:

Brands by name

Popular brands