Deagostini ModelSpace Hummer H1 Assembly Manual Download Page 16 | Manualshive

Page: 16 / 24

background image

HUMMER H1: STEP BY STEP

14

11

22

77

66

44

33

55

Hold the left side mirror over the left side mirror cover, as shown
above, to identify the projections and holes highlighted by the
red arrows.

Fit the projection on each component into its corresponding
hole on the other component.

Insert the side mirror pin into the hole in the
bottom of the side mirror cover.

Locate the hole in the bottom of the side mirror cover into which
the side mirror pin fits.

There is a hole near the base of the mirror cover into
which the side mirror arm fits. Use the photo to identify
the correct orientation of the two parts.

Press down firmly on the mirror, pushing it into the cover.

Insert one of the side mirror arms into the hole in the base of the
mirror cover.

«
...
14
15
16
17
18
...
»

Summary of Contents for ModelSpace Hummer H1

























Reviews:

No comments

Related manuals for ModelSpace Hummer H1

Brand: Jamara Pages: 8

Brand: Jamara Pages: 4

Lindner Geotrac

Brand: Jamara Pages: 12

Ferrari LaFerrari Aperta

Brand: Jamara Pages: 4

Brand: Jamara Pages: 8

Brand: Jamara Pages: 20

Mercedes-AMG G63

Brand: Jamara Pages: 8

Brand: Jamara Pages: 4

XB PRO SUPER LEVANT 57796

Brand: Tamiya Pages: 13

Brand: Sportwerks Pages: 40

Brand: Kogan Pages: 20

Brand: Yokomo Pages: 32

Brand: Associated Electrics Pages: 20

Brand: Jamara Pages: 8

On-Road Racer 4WD

Brand: Reely Pages: 43

Brand: Reely Pages: 60

Brand: Sportwerks Pages: 28

Brand: Amewi Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands