DDK HFC3000II, Instruction Manual

Page: 62 / 216

Chapter 4 Installation
PAGE 4-26
4-7-3. Data Format (RS232C-1)
The fastening result data are output from the RS232C-1 interface at the end of fastening. The data
length of the fastening result data in ASCII format is 79 bytes (corresponding to 79 characters) per
single fastening operation. The format of the data output per Contorller is shown below.
・
Be careful because the decimal point differs according to tool model.
・
The output data of each item are indicated in a right-justified manner.
●
Output Data Format (in the case of ASCII format, with torque being indicated to 2 decimal places and the
rate is indicated to 3 decimal places)
When the fastening judgment is normal (ACCEPT)
COUNT No. : Incremented by +1 at each fastening (stored even when power is shut down, reset in linkage
with erasing of 10,000 records)
ACCEPT COUNT: Counted number of ACCEPT fastening judgments (JDG: Judgment, OCR: Occurrence)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
COUNT No.
ACCEPT
COUNT
CONTORLLER No. WORK No.
30H 30H 30H 31H 30H 31H 30H 31H 20H 20H 30H 31H 20H 20H
0 0 0 1 0 1 0 1 0 1
15 16 17 18 19 20 21 22 23 24 25 26 27 28
PEAK TORQUE JDG OCR FINAL ANGLE JDG OCR
31H 32H 2EH 33H 34H 20H 20H 20H 20H 31H 32H 33H 20H 20H
1 2 . 3 4 1 2 3
29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44
FINAL TORQUE JDG OCR RATE1 JDG OCR
31H 32H 2EH 33H 34H 20H 20H 20H 30H 2EH 31H 32H 33H 20H 20H 20H
1 2 . 3 4 0 . 1 2 3
45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
RATE2 JDG OCR RATE3 JDG OCR
30H 2EH 31H 32H 33H 20H 20H 20H 30H 2EH 31H 32H 33H 20H 20H 20H
0 . 1 2 3 0 . 1 2 3
61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76
1ST TIME JDG
OCR
2ND TIME JDG
OCR
20H 31H 30H 2EH 30H 20H 20H 20H 20H 20H 32H 2EH 30H 20H 20H 20H
1 0 . 0 2 . 0
77 78 79
JDG CR LF
4FH 0DH 0AH
O
TOTAL JUDGMENT
"O"(4FH): Fastening judgment
ACCEPT
[PEAK TORQUE] JUDGMENT
"H"(48H): HIGH REJECT
"L"(4CH): LOW REJECT
"A"(41H): ABNORMAL "S"(53H): STOP
"B"(42H): BYPASS
“R”(52H): RESET
“D” (44H): START OFF (Off operation by lever performed during
fastening)
The CAUSE OF REJECT OCR (OCR) is not set in the case of solitary
occurrence of "A," "B," "S," “R,” or “D.”
[FINAL TORQUE], [ANGLE], [RATE], [TIME] JUDGMENT
"H"(48H): HIGH REJECT
"L"(4CH): LOW REJECT
Caution
S0140185-H