background image

PSXX Manual Rev: A             Software Rev: F 

 

   

 

[email protected] 

*Designed by Larry Maier 

*Developed by DCC Specialties 

*US Patent 7,810,435 

 

For DCC Use Only 

New! 

Advanced Circuit Design 

New! 

Current Limiting 

New! 

Automatic Timing Delay 

New! 

Block Occupied Functions 

 

The PSXX Circuit Breaker uses a new advanced design to provide a new level of over-current 

protection for your layout. Before the advent of the PSXX, all circuit breakers used a simple 

low resistance switch to turn off the current if it exceeded a set value. The layout is protected, 

but for the time between the onset of the short and the output switch turning off, the fault is 

connected directly across the booster terminals affecting all blocks connected to the booster. 

The booster will supply up to its maximum current trying to maintain the track voltage. 

Currents as high as 48 amperes can result, depending on your booster and wiring. The large 

current draw then means there is no current left for any other block even if they are protected 

by their own circuit breakers. 

The PSXX series is a product of years of research into problems dealing with false overloads 

that cause premature shut down of DCC Boosters and other Circuit Breakers. These false 

overloads are caused by large capacitors used in sound systems, decoders and lighted 

passenger cars. The overload appears as a short circuit until the capacitors are charged. The 

PSXX Series determines if the load is a true short or just an overload due to a discharged 

capacitor. 

PSXX Versions Available:  

PSXX-1, PSXX-2 & PSXX-3  

                                        

 

Advanced Circuit Design

 limits current to selected current value before circuit opens 

regardless of severity of fault 

 

Current Limiting

 will charge sound decoders without exceeding booster current capability 

 

Default Current Limit/Trip Current 2 amperes 

will work correctly for most layouts. 

 

Select Trip current

 values 1 – 10 in integer steps (1, 2, 3, …., 10) using CV 49 

 

Jumper Select Current

 limits of 1, 2, 3, or 4 amperes  

 

PSXX circuit boards are perforated with score lines

 so you can physically separate and 

divide PSXX-2, & PSXX-3 into individual PSXX-1 units if needed. 

 

Power On/Off by DCC:

 Turn on/off output track power with your DCC Throttle! 

The PSXX-1,2,3 Series

 

DCC Circuit Breaker  

Intelligent, Solid State  

 Block Detection and Network Feed Back

 

Manual Rev A [01.22, Software Rev F [07.22]

 

Summary of Contents for PS 1 Series
























Reviews: