manualshive.com logo in svg

DBL Technology GoIP-1, User Manual, Page: 62 / 69

Share
Download
DBL Technology GoIP-1 User Manual Download Page 62

DBL Technology Co., Ltd. 

 

  GoIP User Manual 

www.dbltek.com 

                                                            Technical Support: [email protected] 

 

62 

Appendix B.

 

SMS To VoIP 

The device receives SMS messages from both GSM and VoIP networks and they are handled according to the 
modes defined below.     

1.

 

Call Function – In this mode, a received SMS is used to implement the “Call Back” function.    The concept 
is to establish a phone call between the called party and the calling party.    The phone number of the called 
party is specified in the GSM SMS message received.    The phone number of the calling party is the SMS 
sender’s number.    The device then sends a SIP INVITE message containing these phone numbers to the SIP 
Server registered.    Three different SIP INVITE message formats are supported and are described below. 

 

a)

 

Mode 1   
SIP Message format: 

 

The “To” field in the SIP INVITE message contains the phone number of the called party.     

 

The “From” field contains the phone number of the calling party.     

 
Once the SIP server receives these two numbers via a SIP INVITE message, it then terminates the SIP call 
(SIP INVITE) and then call both parties via its own phone network.    The device may or may not take part 
in the actual call conversation. 
 
Example:   

SMS content = 8675588228822 
Sender’s number = 861380000000 
SIP Server IP = 192.168.2.1 
SIP Number = 20001 
The INVITE message sent to the SIP Server is: 

 

INVITE sip:

8675588228822

@192.168.2.1:5060;transport=udp SIP/2.0 

Via: SIP/2.0/UDP 192.168.2.237:5060;branch=z9hG4bK363969813 

From: <sip:

8613800000000

@192.168.2.1:5060>;user=phone;tag=65248630 

To: <sip:

8675588228822

@192.168.2.1> 

Call-ID: [email protected] 

CSeq: 2 INVITE 

Contact: <sip:

 8613800000000

@192.168.2.237:5060> 

Max-Forwards: 30 

User-Agent: DBL 

Allow: INVITE, ACK, BYE, CANCEL, OPTIONS, NOTIFY, REFER, REGISTER, MESSAGE, INFO, SUBSCRIBE 

Content-Type: application/sdp 

Content-Length:    226 

 

b)

 

Mode 2   
SIP Message format: 

 

The “To” field in the SIP INVITE message contains the phone number of the called party.     

 

The “From” field contains the SIP number of the line that is associated with the GSM channel 

 

Note:    The VoIP configuration of the device must be set to “Config. By Line mode”.     

 
Only the phone number of the called party is passed to the SIP server via a SIP INVITE message.    This 
mode is designed to use the GSM channel of the device to complete the Call Back function.    Therefore, 
the 

Call OUT via GSM

 parameter of the device must be enabled and the 

Forward Number

 associated 

with this parameter is set to the phone number of the SMS sender.   
 

https://arttel.ru/

https://arttel.ru/shop/gsm-shlyuzy/gsm-shlyuz-goip-4

Summary of Contents for GoIP-1






































































Reviews:

No comments