manualshive.com logo in svg

DBL Technology GoIP-1, User Manual, Page: 47 / 69

Share
Download
DBL Technology GoIP-1 User Manual Download Page 47

DBL Technology Co., Ltd. 

 

  GoIP User Manual 

www.dbltek.com 

                                                            Technical Support: [email protected] 

 

47 

 

Parameter 

Description 

Default Value 

1.

 

SMS to VoIP 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Call Mode 

 
 

 

Dialing Prefix 

 
 
 
 
 
 
 
 
 
 

 

VoIP Number 

 

 

GSM Number

 

 
 
 
2.

 

SMS Delivery Report 

 

This parameter applies to ALL channels. 
This defines how the device handles received SMS messages. 

 

1.

 

Call Function – This mode is used to support Call Back function via incoming 

GSM  messages.    Appendix  B  describes  the  three  different  modes  of 
operations  in  order  to  meet  the  different  requirements  from  various  SIP 
servers.    Please note that the SIP server registered must be configured for 
this operation. 

 

 

This  parameter  specify  which  SMS  Dial  mode  is  used.    Please  refer  to 
Appendix B for more information on the modes available. 
 
The parameter  is applicable for  SMS  Dial mode.    It allows a prefix to  be 
added to the phone number of the called party. 

 
2.

 

Forward Function – This mode forwards incoming GSM SMS to a SIP terminal 

and a GSM number. 

 

 

 

Incoming  GSM  messages  (SMS)  received  are  forwarded  to  the  SIP  Phone 
Number specified in this parameter. 
Incoming GSM messages (SMS) received are forwarded to the GSM Phone 
Number specified in this parameter.    The channel received the message is 
used to forward the message. 
 
This parameter enables the device to inform the SMS Server when a SMS 
sent from the SMS Server is received by the recipient. 

Disabled 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Disabled 

 
 
 
 
 
 
 
 
 

 

https://arttel.ru/

https://arttel.ru/shop/gsm-shlyuzy/gsm-shlyuz-goip-4

Summary of Contents for GoIP-1






































































Reviews:

No comments