manualshive.com logo in svg

DBL Technology GoIP-1, User Manual, Page: 16 / 69

Share
Download
DBL Technology GoIP-1 User Manual Download Page 16

DBL Technology Co., Ltd. 

 

  GoIP User Manual 

www.dbltek.com 

                                                            Technical Support: [email protected] 

 

16 

3.

 

Web Access Records 
a)

 

Last Client IP – This shows the IP address of the PC for the last web access. 

b)

 

Last Login Time – The shows the time when the last web access occurred. 

c)

 

Current Client IP – This shows the IP address of the PC for the current web access. 

 

4.

 

Call Management section summarizes the both GoIP and GSM configurations and their corresponding 
status.    It is important to note that the VoIP lines and the GSM channels are not mapped to each other 
as a one to one relationship.    For outgoing calls (from VoIP to GSM), the GSM channel selection is based 
on the Routing Prefix.         
VoIP 
a)

 

Line - This is used as a reference in VoIP line configuration. 

b)

 

Mode - This shows the current VoIP Registration mode.    "S" means Single Server Mode.    "L" means 
Config. By Line mode.    "Gx" means Config. by Group mode where x is the group reference number. 
"T" means Trunk Gateway mode. 

c)

 

Login  -  This  shows  the  current  VoIP  registration  status.    "Y"  means  that  the  corresponding  line 
registers to the server successfully.    "N" means the corresponding line fails to register to the server. 

d)

 

Routing Prefix - This shows the current setting for the Routing Prefix.    If it is set, the Routing Prefix 
is used to select the corresponding channel to dial out a call.    Please refer to Section 3.3.3 for more 
information. 

GSM 
e)

 

CH - This corresponds to the physical GSM channel number. 

f)

 

Login - This shows the current GSM Registration status for voice calls. 

g)

 

Call In - This shows the Call IN setting for the corresponding GSM channel.    "Y" means incoming calls 
are  enabled.    "N"  means  incoming  calls  are  disabled  and  the  corresponding  channel  rejects  all 
incoming calls by sending back the hangup ("ATH") command to the GSM network.   

h)

 

Call Out - This shows the Call Out setting for the corresponding GSM channel.    "Y" means outgoing 
calls are enabled and "N" means outgoing calls are disabled.    When the Remain Time for outgoing 
calls reaches zero, the Call Out setting is set to "LOCK" automatically.    To unlock the channel, click 
the corresponding [Reset] button in the Summary page. 

i)

 

Remain Time - This is the same as the "Remain" shown in the Summary page.    If the Talk Time Limit 
in the SIM Page is set, this parameter shows the remaining time allowed for outgoing calls.   

5.2.3

 

GSM   

The GSM page shows the current GSM channels status and information on the GSM modules and the SIM cards 
inserted.     

 

https://arttel.ru/

https://arttel.ru/shop/gsm-shlyuzy/gsm-shlyuz-goip-4

Summary of Contents for GoIP-1






































































Reviews:

No comments