DaVinci Maestro Collection Square Owner'S Manual Download Page 48

Page: 48 / 64

48 Installation

(for qualified installers only)

9/25/17-1468

Maestro

Facing Requirements



Drywall, tile, or other facing (combustible or non-combustible) may be placed along the perimeter off
facing standoff, but must not extend over it. This area must remain open to allow for glass removal
and ventilation.



Fireplace must not be used to support the facing. Heavy facing must be self-supporting.

WARNING

: Do not use adhesive to secure the facing. The high temperatures of the

fireplace may cause adhesives to emit odors. Use mastic or thin set (or other non-
combustible, non-odorous adherent) to attach the facing.

NOTE

: Screws may be used to secure cement board or tile backer to the fireplace. Do not

penetrate the fireplace more than 1/2” (13mm).

Adhesive

Facing Standoff

Facing

(combustible or

non-combustible)

Outer Glass

Drywall Facing

Example

Marble (Thick)

Facing Example

Drywall

Marble

Drywall

Framing

Top of Fireplace

Facing Standoff

Cement Backing Board

Summary of Contents for Maestro Collection Square

































































Search results

Summary of Contents for Maestro Collection Square

Reviews:

Related manuals for Maestro Collection Square

Brands by name

Popular brands

DaVinci Maestro Collection Square, Owner'S Manual

Search results

Summary of Contents for Maestro Collection Square

Reviews:

Related manuals for Maestro Collection Square

Brands by name

Popular brands