DaVinci 72 SS Timber Installation Instructions Manual Download Page 21 | Manualshive

Page: 21 / 24

background image

DaVinci 72” SS Timber Fire Log Set

Installation Instructions

Page 21 of 24

17602248 — 7/25/22

© Travis Industries, Inc.

35. Place more ember chunks on the ember glass installed in the last step.

NOTE:

Make sure that no glass or ember chunks are obstructing the slot where the inner glass will

rest. If anything has fallen into the slot, remove it with a vacuum, small screwdriver, or compressed air.

36. Reinstall the outer glass using the glass lifting suction cup set. Take care not to damage the edges of the glass

when placing it back on the fireplace. Place the outer fireback filler pieces in place. They are held in place by
magnets. Place the bottom edge of the filler piece in the lower corner of the opening and then tilt the filler up until
the magnets secure it to the fireplace.

DRAFT

DRAFT

DRAFT

«
...
19
20
21
22
23
...
»

Summary of Contents for 72 SS Timber

























Reviews:

No comments

Related manuals for 72 SS Timber

Brand: Valor Pages: 6

Brand: Real Flame Pages: 19

Brand: Gas Technologies Pages: 31

Ortal 110 RS/LS

Brand: Oblica Pages: 10

Brand: Lamborghini Caloreclima Pages: 196

Brand: Napoleon Pages: 6

Brand: Jetmaster Pages: 32

Brand: Valor Pages: 46

Brand: Bellfires Pages: 55

Brand: IKOS Pages: 54

BarcelonaLights36ZEN

Brand: IHP Pages: 40

Brand: Rinnai Pages: 36

Brand: Rinnai Pages: 36

Slimfire Zero Clearance Box

Brand: Rinnai Pages: 2

Brand: Rinnai Pages: 32

Brand: Rush Pages: 10

Brand: Heat&Glo Pages: 28

Brand: ClassicFlame Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands