DaVinci 72 SS Timber Installation Instructions Manual Download Page 4 | Manualshive

Page: 4 / 24

background image

DaVinci 72” SS Timber Fire Log Set

Installation Instructions

Page 4 of 24

17602248 — 7/25/22

© Travis Industries, Inc.

Firebox Preparation

1. Remove the (6) screws that secure the burner to the fireplace. Set the screws aside for reinstallation.

2. Remove the burner by lifting the assembly straight up and remove it from the fireplace.

3. Use a 1/4" driver to remove the screws (4) screws (1 on each end of both log grates) that secure the log grates

to the fireplace. Set the screws aside for reinstallation.

DRAFT

DRAFT

DRAFT

«
...
2
3
4
5
6
...
»

Summary of Contents for 72 SS Timber

























Reviews:

No comments

Related manuals for 72 SS Timber

Brand: Valor Pages: 12

Brand: Superior Pages: 18

Direct Vent Gas Fireplace

Brand: Element4 Pages: 92

Brand: Majestic Pages: 24

Brand: EdilKamin Pages: 19

Brand: Yosemite Pages: 15

Brand: Uberhaus Pages: 7

CASUAL FIRESIDE 5110-2875O

Brand: OW Lee Pages: 28

CASUAL FIRESIDE 5110-2442O-E

Brand: OW Lee Pages: 28

Brand: OW Lee Pages: 28

Brand: Hearth and Home Technologies Pages: 2

Brand: Hearth and Home Technologies Pages: 10

Brand: Quadra-Fire Pages: 56

Brand: Quadra-Fire Pages: 24

Brand: Heat & Glo Pages: 37

Brand: Heat & Glo Pages: 62

Brand: Heat & Glo Pages: 79

Insert Studio LHEC30

Brand: Vermont Castings Pages: 53

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands