Davicom DM9000A Application Notes Download Page 16 | Manualshive

Page: 16 / 38

background image

DM9000A

APPLICATION NOTES

Preliminary 16
Version: DM9000A-AN-V121
November 27, 2007

3 GPIO3

0,

RW

If GP3 is output port, GPR Bit [3] sets to "1" to
enable the pin 28 output high or sets to "0" to enable
the pin 28 output low.
If GP3 is input port, the value of GPR Bit [3] is "1" to
represent a high signal is received. In contract, the
value of GPR Bit [3] is "0" to represent a low signal
is received.

2 GPIO2

0,

RW

If GP2 is output port, GPR Bit [2] sets to "1" to
enable the pin 29 output high or sets to "0" to enable
the pin 29 output low.
If GP2 is input port, the value of GPR Bit [2] is "1" to
represent a high signal is received. In contract, the
value of GPR Bit [2] is "0" to represent a low signal
is received.

1 GPIO1

0,

RW

If GP1 is output port, GPR Bit [1] sets to "1" to
enable the pin 31 output high or sets to "0" to enable
the pin 31 output low.
If GP1 is input port, the value of GPR Bit [1] is "1" to
represent a high signal is received. In contract, the
value of GPR Bit [1] is "0" to represent a low signal
is received.

0 PHYPD

1,

RW

"1": power down the internal PHY
"0": power up the internal PHY.

Table 3.5 General Purpose Register (GPR) Table

«
...
14
15
16
17
18
...
»

Summary of Contents for DM9000A







































Reviews:

No comments

Related manuals for DM9000A

Brand: Lawler Pages: 6

Brand: Data Aire Pages: 28

Brand: Eaton Pages: 12

Brand: Farfisa Pages: 20

Brand: Racal Instruments Pages: 64

Brand: Veeder-Root Pages: 27

Brand: Valve Concepts Pages: 18

Brand: K&K Pages: 6

FOUNDATION 3730-5

Brand: Samson Pages: 132

Brand: Samson Pages: 68

Brand: Samson Pages: 128

Brand: Samson Pages: 68

Brand: X-POWER Pages: 24

Brand: Samson Pages: 80

Brand: Haehne Pages: 44

Brand: UNISENSE Pages: 16

Brand: Xylem Pages: 48

Brand: B&G Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands