manualshive.com logo in svg

Datex-Ohmeda S/5 M-NIBP, Technical Reference Manual Slot

Share
Download
Datex-Ohmeda S/5 M-NIBP Technical Reference Manual Slot Download Page 26

Datex-Ohmeda S/5 monitors

Document No. 800 1015-1

22

4.3

 

Troubleshooting flowchart

Does

another module

work in the

same slot?

Possible fault in

NIBP module.

START

Remove all

modules from

C.Monitor Frame.

Fault not in NIBP

module.

LED

check in

Service Menu

OK?

Key

check in

Service Menu

OK?

Pump

check in

Service Menu

OK?

Leak test

in Service

Menu OK?

Insert NIBP

module and turn

power on.

Does

the fault still

appear?

Module ID on

screen?

Error

message on

screen?

See error code

explanation in

Service Manual

and fix it.

Do they work?

Check tubes and

connectors. Find

leak and fix it.

Check and replace

NIBP board.

Replace LED

board.

Check keyboard

connector. If OK,

change front panel.

Check pump

connector. If OK,

change pump.

Check and replace

NIBP board.

OK?

Replace NIBP

module.

OK?

NO

YES

NO

YES

YES

YES

YES

YES

YES

YES

NO

NO

NO

NO

NO

NO

NO

NO

Figure 4

NIBP Module troubleshooting flowchart

Summary of Contents for S/5 M-NIBP

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands