manualshive.com logo in svg

Datex-Ohmeda S/5 M-NIBP, Technical Reference Manual Slot

Share
Download
Datex-Ohmeda S/5 M-NIBP Technical Reference Manual Slot Download Page 25

NIBP Module, M-NIBP

Document No. 800 1015-1

21

4.2

 

NIBP error code explanation

Code

Explanation

0

RAM failure

Memory failure. Change NIBP board.

1

ROM checksum error

Memory failure. Change NIBP board.

2

+15V failure

Check short circuits. Change NIBP board.

3

-15V failure

Check short circuits. Change NIBP board.

4

EEPROM protection switch error. (only with S-STD93)

Turn the toggle switch to the left at the bottom of the module.

5

Calibration not protected. (only with S-STD93)

Protect calibration by selecting Protection ON in the NIBP calibration menu

6

ADC error

ADC circuit failure. Change NIBP board.

7

Watchdog time too short

Change NIBP board.

8

Watchdog time too long

Change NIBP board.

9

Watchdog activated

Change NIBP board.

10

EEPROM checksum error

Memory failure. Change NIBP board.

11

Auto zero range exceeded

Calibrate NIBP.

12

Communication break

Temporal break down of communication from monitor detected. Automatic

recovery.

14

Too early Auto Start (needs 25 seconds without pressure).

Summary of Contents for S/5 M-NIBP

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands