manualshive.com logo in svg

Datex-Ohmeda S/5 M-NIBP, Technical Reference Manual Slot

Share
Download
Datex-Ohmeda S/5 M-NIBP Technical Reference Manual Slot Download Page 16

Datex-Ohmeda S/5 monitors

Document No. 800 1015-1

12

7.

 

Enter the NIBP module service menu:

Parameters - NIBP

Check that the ‘Timeouts’, ‘Bad checksums’ and ‘Bad c-s by mod’ values are not increasing

faster than by 50 per second. Check also that the NIBP board memories have passed the

internal memory test, i.e. the ‘RAM’, ‘ROM’ and ‘EEPROM’ show all OK.

?

8.

 

Check the front panel LEDs and membrane keys.

Select 

Buttons/Leds

Highlight the text 

Auto ON

. Check that the LED for the autocycle measurement is turning on

and off on the module front panel when pressing the ComWheel. Check also the other LEDs

by selecting 

Manual ON

, 

STAT ON

 and 

Measur. ON

.

Press each of the module’s membrane keys at least for one second. Check that the pressed

key is identified, i.e. the text OFF changes to ON for the key in the menu.

?

9.

 

Check the pump and valves.

Select 

Pneumatics

 from the NIBP menu. Connect a pressure manometer to the NIBP

module cuff connector.

Highlight 

Start Pump 

and press the ComWheel. Check that the pump turns on and the

pressure inside the tubing system starts to increase. Stop the pump by pressing the

ComWheel again when the pressure reaches 280 mmHg.

Highlight 

Open Exh1

. Press the ComWeel and check that the pressure inside the tubing

system starts to drop then press the ComWheel again. Check the other exhaust valve by the

same way by selecting 

Open Exh2 

from the menu.

If necessary, turn the pump on again for a moment to increase the pressure inside the

tubing system.

Highlight 

Open Zerovalve

. Press the ComWheel and check that the pressure B1 

≅

 0 mmHg.

Close the zero valve by pressing the ComWheel again and check that the pressure B1 is

equal with the pressure B2.

Highlight 

Set Valve

. Press the ComWheel and set the value under the text ‘Pulse Valve’ to

number 150 by turning the ComWheel. Press the ComWheel again and check that the

pressure inside the tubing system starts to drop. Finish the test by selecting 

Previous Menu

.

?

Summary of Contents for S/5 M-NIBP

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands