Datamax PrintPAD 1700 User Manual Download Page 34

Page: 34 / 145

PRINTPAD MC70 USER'S GUIDE

Agency Approvals

FCC Notice

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, it may cause harmful interference to radio

communications. However there is no guarantee that interference

will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more of

the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment to an outlet on a circuit different from
that to which the receiver is connected.

•

Consult the dealer or an experienced radio/TV technician for
help.

Applicable Directive

•

89/336/EEC, 73/23/EEC

Applicable Standards

•

EN55022 (1998)

•

EN55024 (1998)

•

EN60950 (1992)

Summary of Contents for PrintPAD 1700


















































































































































Search results

Summary of Contents for PrintPAD 1700

Reviews:

Related manuals for PrintPAD 1700

Brands by name

Popular brands

Datamax PrintPAD 1700, User Manual

Search results

Summary of Contents for PrintPAD 1700

Reviews:

Related manuals for PrintPAD 1700

Brands by name

Popular brands