Datamax PrintPAD 1700 User Manual Download Page 28

Page: 28 / 145

PRINTPAD MC70 USER'S GUIDE

Audio Indicators

Orange flash -
slow

Charge has timed out.

Restart battery
charge (battery
may be bad).

Orange flash -
fast

Internal code error.

Remove the
battery, then
re-connect A/C
power.

Orange, red, or
green flash -
fast

When the AC adapter is
plugged into the printer's
power port, the battery
status LED flashes orange,
red, or green (depending on
the battery status LED color
that is initially displayed) to
indicate the AC adapter is
plugged in.

None.

Beep(s)

Description

Action

Printer wakes up.

None.

Out of paper.

Install paper.

Low battery.

Charge battery.

1 short

RF power is on (when blue,
RF power button is pressed
and power was turned off).

None.

2 short

RF power is off (when blue,
RF power button is pressed
and power was turned on).

None.

1 long

Boot code is starting or
restarting (when
downloading new firmware).

Redownload
firmware.

8 short

CRC error in firmware.

Redownload
firmware.

Summary of Contents for PrintPAD 1700


















































































































































Search results

Summary of Contents for PrintPAD 1700

Reviews:

Related manuals for PrintPAD 1700

Brands by name

Popular brands

Datamax PrintPAD 1700, User Manual

Search results

Summary of Contents for PrintPAD 1700

Reviews:

Related manuals for PrintPAD 1700

Brands by name

Popular brands