Datamax PrintPAD 1700 User Manual Download Page 121 | Manualshive

Page: 121 / 145

background image

Chapter 4 — Printer Options

22

PrintPAD Series CN70/70e & CN51 User Guide

DEX/UCS Port

DEX/UCS Port: Use this illustration to locate the DEX/UCS port on the printer.

The direct exchange (DEX)/UCS port can only be used with the Datamax

-

O’Neil by Honeywell

-

approved DEX cable (P/N: 210237

-

xxx).

When the DEX cable is plugged into the data port, the printer automatically
turns off to allow data transfer between the mobile computer and the DEX port.

Remove the DEX cable to resume normal connection to the printer.

DEX/UCS port

Note: Do not unplug the cable in the middle of the data transfer session. Your
application needs to be programmed to communicate in the DEX/UCS
language.

«
...
119
120
121
122
123
...
»

Summary of Contents for PrintPAD 1700


















































































































































Reviews:

No comments

Related manuals for PrintPAD 1700

Brand: Xerox Pages: 24

Brand: Fargo Pages: 6

Brand: Fargo Pages: 90

Brand: Fargo Pages: 126

Brand: FARGO electronics Pages: 278

Brand: G3D Pages: 4

Brand: Canon Pages: 198

Brand: Oki Pages: 4

Brand: Oki Pages: 40

Brand: Oki Pages: 507

Brand: Oki Pages: 176

Brand: Samsung Pages: 351

464de - X B/W Laser

Brand: Lexmark Pages: 27

Brand: A&D Pages: 16

ApeosPort-III C7600

Brand: Xerox Pages: 369

Brand: Oki Pages: 120

Brand: GCC Technologies Pages: 8

Brand: Patton electronics Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands