DataCard ImageCard series User Manual Download Page 134

Page: 134 / 159

B-11

User’s Guide for the Magna™ Class Printer

Printer components

The Magna Class printer has a replaceable printhead. In addition,
you can order additional or replacement parts for the printer. This
section describes the printer parts you can order.

Printhead cartridge

The Magna Class printer has a replaceable printhead. The printhead
is subject to wear and has a direct impact on print quality.

Select the printhead to order based on the printer series.The
following printheads are available.

Figure B-6: Magna Class replaceable printhead cartridge

Do not touch the printing edge of the printhead in the printhead

cartridge. If you do, use the cleaning pen to clean it. See

“Cleaning the printhead” on page 4-6

Keep a replacement printhead in stock so it is available when you
need it.

Printer
series

Printhead
type

Printhead type label Part number

ImageCard

Full color

Three colors

547675-001

UltraGrafix

Monochrome

All black

547674-001

Printhead type label

Printhead-do not
touch this surface

MagnaUserGuide.book Page 11 Friday, May 5, 2000 1:09 PM

Summary of Contents for ImageCard series
































































































































































Search results

Summary of Contents for ImageCard series

Reviews:

Related manuals for ImageCard series

Brands by name

Popular brands

DataCard ImageCard series, User Manual

Search results

Summary of Contents for ImageCard series

Reviews:

Related manuals for ImageCard series

Brands by name

Popular brands