Danfoss vlt fcd 302, Operating Manual, Page: 54 / 84

8-19 Product Code ExpressionLimit 1 set-up TRUE 0 Uint32
8-3* FC Port Settings
8-30 Protocol [0] FC 1 set-up TRUE – Uint8
8-31 Address 1 N/A 1 set-up TRUE 0 Uint8
8-32 FC Port Baud Rate ExpressionLimit 1 set-up TRUE – Uint8
8-33 Parity / Stop Bits
[0] Even Parity, 1
Stop Bit 1 set-up TRUE – Uint8
8-34 Estimated cycle time 0 ms 2 set-ups TRUE -3 Uint32
8-35 Minimum Response Delay 10 ms 1 set-up TRUE -3 Uint16
8-36 Max Response Delay ExpressionLimit 1 set-up TRUE -3 Uint16
8-37 Max Inter-Char Delay ExpressionLimit 1 set-up TRUE -5 Uint16
8-4* FC MC protocol set
8-40 Telegram Selection
[1] Standard
telegram 1 2 set-ups TRUE – Uint8
8-41 Parameters for Signals 0 All set-ups FALSE – Uint16
8-42 PCD Write Configuration ExpressionLimit 2 set-ups TRUE 0 Uint16
8-43 PCD Read Configuration ExpressionLimit 2 set-ups TRUE 0 Uint16
8-5* Digital/Bus
8-50 Coasting Select [3] Logic OR All set-ups TRUE – Uint8
8-51 Quick Stop Select [3] Logic OR All set-ups TRUE – Uint8
8-52 DC Brake Select ExpressionLimit All set-ups TRUE – Uint8
8-53 Start Select [3] Logic OR All set-ups TRUE – Uint8
8-54 Reversing Select [3] Logic OR All set-ups TRUE – Uint8
8-55 Set-up Select [3] Logic OR All set-ups TRUE – Uint8
8-56 Preset Reference Select [3] Logic OR All set-ups TRUE – Uint8
8-57 Profidrive OFF2 Select [3] Logic OR All set-ups TRUE – Uint8
8-58 Profidrive OFF3 Select [3] Logic OR All set-ups TRUE – Uint8
8-8* FC Port Diagnostics
8-80 Bus Message Count 0 N/A All set-ups TRUE 0 Uint32
8-81 Bus Error Count 0 N/A All set-ups TRUE 0 Uint32
8-82 Slave Messages Rcvd 0 N/A All set-ups TRUE 0 Uint32
8-83 Slave Error Count 0 N/A All set-ups TRUE 0 Uint32
8-9* Bus Jog
8-90 Bus Jog 1 Speed 100 RPM All set-ups TRUE 67 Uint16
8-91 Bus Jog 2 Speed ExpressionLimit All set-ups TRUE 67 Uint16
5.3.10 9-** Profibus
Par-
ameter # Parameter description Default value 4 set-up Change during
operation
Conversion
index
Type
9-00 Setpoint 0 N/A All set-ups TRUE 0 Uint16
9-07 Actual Value 0 N/A All set-ups FALSE 0 Uint16
9-15 PCD Write Configuration ExpressionLimit 1 set-up TRUE – Uint16
9-16 PCD Read Configuration ExpressionLimit 2 set-ups TRUE – Uint16
9-18 Node Address 126 N/A 1 set-up TRUE 0 Uint8
9-19 Drive Unit System Number 1034 N/A All set-ups TRUE 0 Uint16
9-22 Telegram Selection [100] None 1 set-up TRUE – Uint8
9-23 Parameters for Signals 0 All set-ups TRUE – Uint16
9-27 Parameter Edit [1] Enabled 2 set-ups FALSE – Uint16
9-28 Process Control
[1] Enable cyclic
master 2 set-ups FALSE – Uint8
9-44 Fault Message Counter 0 N/A All set-ups TRUE 0 Uint16
9-45 Fault Code 0 N/A All set-ups TRUE 0 Uint16
9-47 Fault Number 0 N/A All set-ups TRUE 0 Uint16
Programming
VLT
®
Decentral Drive FCD 302
52 Danfoss A/S © 05/2016 All rights reserved. MG04F402
5 5