Danfoss vlt fcd 302, Operating Manual, Page: 44 / 84

5.3.2 1-** Load/Motor
Par-
ameter # Parameter description Default value 4 set-up Change during
operation
Conversion
index
Type
1-0* General Settings
1-00 Configuration Mode ExpressionLimit All set-ups TRUE – Uint8
1-01 Motor Control Principle ExpressionLimit All set-ups FALSE – Uint8
1-02 Flux Motor Feedback Source [1] 24V encoder All set-ups FALSE – Uint8
1-03 Torque Characteristics [0] Constant torque All set-ups TRUE – Uint8
1-04 Overload Mode [0] High torque All set-ups FALSE – Uint8
1-05 Local Mode Configuration
[2] As mode par
1-00 All set-ups TRUE – Uint8
1-06 Clockwise Direction [0] Normal All set-ups FALSE – Uint8
1-07 Motor Angle Offset Adjust [0] Manual All set-ups FALSE – Uint8
1-1* Special Settings
1-10 Motor Construction [0] Asynchron All set-ups FALSE – Uint8
1-11 Motor Model ExpressionLimit All set-ups FALSE – Uint8
1-18 Min. Current at No Load 0 % All set-ups TRUE 0 Uint16
1-2* Motor Data
1-20 Motor Power [kW] ExpressionLimit All set-ups FALSE 1 Uint32
1-21 Motor Power [HP] ExpressionLimit All set-ups FALSE -2 Uint32
1-22 Motor Voltage ExpressionLimit All set-ups FALSE 0 Uint16
1-23 Motor Frequency ExpressionLimit All set-ups FALSE 0 Uint16
1-24 Motor Current ExpressionLimit All set-ups FALSE -2 Uint32
1-25 Motor Nominal Speed ExpressionLimit All set-ups FALSE 67 Uint16
1-26 Motor Cont. Rated Torque ExpressionLimit All set-ups FALSE -1 Uint32
1-29 Automatic Motor Adaptation (AMA) [0] Off All set-ups FALSE – Uint8
1-3* Adv. Motor Data
1-30 Stator Resistance (Rs) ExpressionLimit All set-ups FALSE -4 Uint32
1-31 Rotor Resistance (Rr) ExpressionLimit All set-ups FALSE -4 Uint32
1-33 Stator Leakage Reactance (X1) ExpressionLimit All set-ups FALSE -4 Uint32
1-34 Rotor Leakage Reactance (X2) ExpressionLimit All set-ups FALSE -4 Uint32
1-35 Main Reactance (Xh) ExpressionLimit All set-ups FALSE -4 Uint32
1-36 Iron Loss Resistance (Rfe) ExpressionLimit All set-ups FALSE -3 Uint32
1-37 d-axis Inductance (Ld) ExpressionLimit All set-ups FALSE -4 Int32
1-39 Motor Poles ExpressionLimit All set-ups FALSE 0 Uint8
1-40 Back EMF at 1000 RPM ExpressionLimit All set-ups FALSE 0 Uint16
1-41 Motor Angle Offset 0 N/A All set-ups TRUE 0 Int16
1-46 Position Detection Gain 100 % All set-ups TRUE 0 Uint16
1-47 Torque Calibration ExpressionLimit All set-ups TRUE – Uint8
1-5* Load Indep. Setting
1-50 Motor Magnetisation at Zero Speed 100 % All set-ups TRUE 0 Uint16
1-51
Min Speed Normal Magnetising
[RPM]
ExpressionLimit All set-ups TRUE 67 Uint16
1-52 Min Speed Normal Magnetising [Hz] ExpressionLimit All set-ups TRUE -1 Uint16
1-53 Model Shift Frequency ExpressionLimit All set-ups FALSE -1 Uint16
1-54 Voltage reduction in fieldweakening 0 V All set-ups FALSE 0 Uint8
1-55 U/f Characteristic - U ExpressionLimit All set-ups TRUE -1 Uint16
1-56 U/f Characteristic - F ExpressionLimit All set-ups TRUE -1 Uint16
1-57 Torque Estimation Time Constant 150 ms All set-ups TRUE -3 Uint16
1-58 Flying Start Test Pulses Current ExpressionLimit All set-ups FALSE 0 Uint16
1-59 Flying Start Test Pulses Frequency ExpressionLimit All set-ups FALSE 0 Uint16
1-6* Load Depen. Setting
1-60 Low Speed Load Compensation 100 % All set-ups TRUE 0 Int16
Programming
VLT
®
Decentral Drive FCD 302
42 Danfoss A/S © 05/2016 All rights reserved. MG04F402
5 5