copied to the frequency converter to which the control
panel is attached. Select
[3] Download size-independent
parameter
to download only the size-independent
parameters. This is used when downloading to a frequency
converter with a different rated power size than that from
which the parameter set-up originates.
NOTICE
Upload/download can only be performed in stop mode.
Download can only be performed to a adjustable
frequency drive with the same software version number,
see parameter
626 Database identification no.
008
Display scaling of output frequency
Value:
0.01 - 100.00
1.00
Function:
In this parameter, the factor is selected by which the
output frequency is to be multiplied. The value is shown in
the display, provided
parameters 009-012 Display readout
have been set to
[5] Output frequency x scaling
.
Description of choice:
Set the required scaling factor.
009
Large display readout
Value:
No readout (none)
[0]
Resulting reference [%]
(reference [%])
[1]
Resulting reference [unit]
(reference [unit])
[2]
Feedback [unit] (feedback [unit])
[3]
Frequency [Hz] (Frequency [Hz])
[4]
Output frequency x scaling
(frequency x scale)
[5]
Motor current [A] (Motor current [A])
[6]
Torque [%] (Torque [%])
[7]
Power [kW] (Power [kW])
[8]
Power [HP] (Power [HP][US])
[9]
Motor voltage [V]
(Motor voltage [V])
[11]
DC link voltage [V]
(DC link voltage [V])
[12]
Thermal load motor [%]
(Motor thermal [%])
[13]
Thermal load [%]
(FC. thermal[%])
[14]
Running hours [Hours]
(RUNNING HOURS])
[15]
Digital input [Bin]
(Digital input[bin])
[16]
Analog input 53 [V]
(analog input 53 [V])
[17]
Analog input 60 [mA]
(analog input 60 [mA])
[19]
Pulse reference [Hz]
(Pulse ref. [Hz])
[20]
External reference [%]
(external ref. [%])
[21]
Status word [Hex] (Status word [hex])
[22]
Heatsink temperature [°C]
(Heatsink temp [°C])
[25]
Alarm word [Hex] (Alarm word [hex])
[26]
Control word [Hex] (Control word [Hex])
[27]
Warning word [Hex]
(warning word [Hex])
[28]
Extended status word [Hex]
(Ext. status [hex])
[29]
Communication option card warning
(COMM OPT WARN [HEX])
[30]
Pulse count
(PULSE COUNTER)
[31]
Power [W]
(POWER [W])
[32]
Function:
Use this parameter to select the data value to display in
the LCP 2 control unit display line 2 when the frequency
converter is switched on. The display is also included in
the scrollbar in display mode. Use
parameters 010-012
Display readout
to select 3 more data values, which are
displayed in display line 1.
Description of choice:
No readout
can only be selected in
parameters 010-012
Small display readout
.
Resulting reference [%]
gives, as a percentage, the resulting
reference in the range from Minimum reference, Ref
MIN
to
Maximum reference, Ref
MAX
.
Reference [unit]
gives the resulting reference with unit Hz
in
Open loop
. In
Closed loop
, the reference unit is selected
in
parameter 416 Process units
.
Feedback [unit]
gives the resulting signal value using the
unit/scaling selected in
parameter 414 Minimum feedback,
FB
LOW
,
415 Maximum feedback, FB
HIGH
and
416 Process units
.
Frequency [Hz]
gives the output frequency of the frequency
converter.
Output frequency x scaling [-]
equals the present output
frequency f
M
multiplied by the factor set in
parameter 008
Display scaling of output frequency
.
Motor current [A]
gives the phase current of the motor
measured as an effective value.
Torque [%]
denotes the motor's present load in relation to
the motor's rated torque.
Power [kW]
gives the present power that the motor is
absorbing in kW.
Power [HP]
gives the present power that the motor is
absorbing in HP.
Motor voltage [V]
gives the voltage supplied to the motor.
Programming
Design Guide
MG27E402
Danfoss A/S © Rev. May/2014 All rights reserved.
63
4
4
