manualshive.com logo in svg

Danfoss VACON 100 industrial, Installation Manual, Page: 54 / 79

Share
Download
Danfoss VACON 100 industrial Installation Manual Download Page 54

8

vacon • 52

APPENDIX 2 - CONTROL AND STATUS WORD

Local contacts: http://drives.danfoss.com/danfoss-drives/local-contacts/

8.2

Status Word Descriptions

The Status word is composed of 32 bits. FBFixedStatusWord consist of the first 16 bits. FBGen-
eralStatusWord consist of the remaining 16 bits. While the functionality of FBFixedStatusWord is 
fixed in the VACON

®

 standard applications, the functionality of FBGeneralStatusWord is totally 

application specific and can vary even in the VACON

®

 standard applications.

The meanings of FBFixedStatusWord bits are described below. Unused bits have to be set to zero..

Table 51. FBFixedStatusWord bits

Bit

Function

Description

B0

Ready

0

Drive  is  not  ready.

1

Drive is ready to run.

B1

Run

0

Motor is not running.

1

Motor is running.

B2

Direction

0

Motor is running clockwise.

1

Motor is running counterclockwise.

B3

Fault

0

No  fault  active.

1

Drive has an active fault.

B4

Alarm

0

No alarm active.

1

Drive has active alarm.

B5

At reference

0

Motor is not running at reference speed.

1

Motor is running at reference speed.

B6

Zero speed

0

Motor is not at zero speed.

1

Motor is running at zero speed.

B7

Flux ready

0

Motor is not magnetized.

1

Motor is magnetized.

B8-B12

Reserved

Summary of Contents for VACON 100 industrial
















































































Reviews:

No comments