Home
/
Danfoss
/
Series 40 M46 Tandem
/
Service Manual

Danfoss Series 40 M46 Tandem, Service Manual, Page: 37 / 48

Share

22 pages before
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48

Page: 37 / 48

Danfoss Series 40 M46 Tandem Service Manual Download Page 37

P107 958E

Servo piston

Alignment slot

3. Install neutral return spring (1214), neutral return bracket (1216), handle (1215), and washer (1235)

onto spool (1207).

4. Using a 1/2 in. hex wrench, install lock nut (1213). Torque to 15 N•m [11 lbf•ft].
5. Lubricate and install spool (1207) into sleeve (1402).
6. Using a 3/8 in. hex wrench, install screw (1210). Torque to 14 N•m [10 lbf•ft]. See

Manual Displacement

Control Neutral-Return Bracket Adjustment

on page 23, for adjustment procedure.

Manual displacement control

P106 639E

1213
1/2 in

1210
3/8 in

302

1214

1216

1215

1208

1235

1207

303

1209

1402

Electronic displacement control/hydraulic displacement control

Removal

If you suspect control of failure, replace control and test pump for proper operation. When installing
control, ensure that sleeve groove engages spring pin on swashplate.

Service Manual

Series 40 M46 Variable Pumps

Minor repair

©

Danfoss | September 2017

11026743 | AX00000027en-US0202 | 37

«
...
35
36
37
38
39
...
»

Summary of Contents for Series 40 M46 Tandem

















































Reviews:

No comments