Danfoss Series 40 M46 Tandem Service Manual Download Page 31 | Manualshive

Page: 31 / 48

Danfoss Series 40 M46 Tandem Service Manual Download Page 31

5. Remove pin (604) and key (605).

Charge pump removal/installation

155

141

142

603

605

604

1503

1502
9/16 in
43Nm [32 ft•lb]

1504

1506
9/16 in
30Nm [20 ft•lb]

1505

P106 636E

Inspection

Inspect the gerotor (603) and gerotor cover (155) for wear, scratches or pitting. If any component

shows signs of wear, scratching, or pitting, relpace all components. Inspect pin (604) and key (605) for

damage, and replace parts if necessary. Replace O-ring (141), load ring (142), and seal (1504)

whenever charge pump is disassembled.

Reassembly

Charge pump parts are available as a complete set

1. Install key (605). Lubricate and install gerotor assembly (603).
2. Install pin (604) and gerotor cover (155).
3. Lubricate and install new O-ring (141) and load ring (142). Install auxiliary pad (1503).

Service Manual

Series 40 M46 Variable Pumps

Minor repair

©

Danfoss | September 2017

11026743 | AX00000027en-US0202 | 31

«
...
29
30
31
32
33
...
»

Summary of Contents for Series 40 M46 Tandem

















































Reviews:

No comments