manualshive.com logo in svg

Danfoss Series 40 M46 Tandem, Service Manual, Page: 36 / 48

Share
Download
Danfoss Series 40 M46 Tandem Service Manual Download Page 36

3. Operate pump at full range of controls to ensure proper machine operation.

Bypass valve

P106 653E

1002

1003

1001
         5/8 in
         20 Nm [15 ft•lb]

Manual displacement control

Removal

1. Using a 3/8 in. hex wrench, remove screw (1210). Remove manual control spool assembly from pump

housing.

2. Using a 1/2 in. hex wrench, remove lock nut (1213). Remove lock washer (1235), handle (1215),

neutral return bracket (1216), and spring (1214) from spool (1207).

Mark the location of neutral return bracket (1216) before disassembly.

3. Remove and discard backup ring (1209) and O-ring (303) from spool.
4. Remove sleeve (1402). Remove and discard backup ring (1208) and O-ring (302).

Inspection

Inspect all parts of control assembly. Replace any damaged parts. Inspect spool and sleeve for

grooves, scratches, and other damage. If spools are damaged, replace them. Inspect sleeve bore in

housing for damage.

Reassembly

1. Lubricate and install O-ring (302) and backup ring (1208) onto sleeve (1402). Lubricate and install

sleeve (1402) into motor housing.

When installing sleeve (1402), ensure that sleeve groove engages spring pin on swashplate.

2. Lubricate and install O-ring (303) and backup ring (1209) onto spool (1207).

Install control spool (1207) with alignment slot facing servo piston.

Service Manual

Series 40 M46 Variable Pumps

Minor repair

 

36 | 

©

 Danfoss | September 2017

11026743 | AX00000027en-US0202

Summary of Contents for Series 40 M46 Tandem

















































Reviews:

No comments