Danfoss OSPE Service Manual Download Page 42

Page: 42 / 48

This section describes minimum tests needed, when the OSPE steering valve has been disassembled and
reassembled.

OSPEDC LSRM with integrated priority valve:

PVE

Electronics

OSP

P301 171

Set up for testing

A universal hydraulic work bench is required for this setup. The work bench must support the following
pump capacity.

•

25 l/min and up to 210 bar pressure for relief valve setting and steering test

•

3 l/min and up to 280 bar pressure for shock valve setting

The hydraulic oil must have a viscosity of 21 cSt. at 50°C with a maximum degree of contamination
according to ISO 4406: 21/19/16.

Set up OSPE with integrated priority valve

1. Connect double rod cylinder to L and R ports of OSPE.
2. Connect pressure gauges to all ports of OSPE.
3. Connect steering column and steering wheel to the input shaft of the OSPE.

Service Manual

OSPE Steering Valve

Test and valve setting of OSPE

L1506577 • Rev 0001 • August 2015

Summary of Contents for OSPE

















































Search results

Summary of Contents for OSPE

Reviews:

Related manuals for OSPE

Brands by name

Popular brands

Danfoss OSPE, Service Manual

Search results

Summary of Contents for OSPE

Reviews:

Related manuals for OSPE

Brands by name

Popular brands