Danfoss OSPE Service Manual Download Page 10

Page: 10 / 48

Tools for OSPE

Tools

Holding tool for the entire steering valve.
Material: Appropriate metal or hard plastic
This tool is not available from Danfoss.

90±1

ø46±0.5

120±2

2xø15±0.1

5±1

20±1

150±2

100±2

7x51.4˚

ø64

ø15+0.5/-0

1x45˚

93±0.5

90±1

P301 787

Assembly tool for dust seal.

Material: Free cutting steel.
This tool is not available from Danfoss.

0.5x45°

ø26±0.1

min ø40

min 35

100±5

P301 643

Assembly tool for shaft seal, O-ring/Roto Glyd type: Code

number: 11092408.

This tool has been modified by January 2015. The upper

end of outer tube has knurled surface on 25 mm from top

only (was 35 mm). Tool with 35 mm knurled surface can

be modified by grinding off 10 mm of the knurled

surface.

Service Manual

OSPE Steering Valve

Tools

L1506577 • Rev 0001 • August 2015

Summary of Contents for OSPE

















































Search results

Summary of Contents for OSPE

Reviews:

Related manuals for OSPE

Brands by name

Popular brands

Danfoss OSPE, Service Manual

Search results

Summary of Contents for OSPE

Reviews:

Related manuals for OSPE

Brands by name

Popular brands