Danfoss H1 069 Service Manual Download

Page: 21 / 68

Overview

Specifications and operating parameters for pumps are given here for reference.

General Specifications

Design

Axial piston pump of cradle swashplate design with variable displacement

Direction of rotation

Clockwise, counterclockwise

Pipe connections

Main pressure ports: SAE straight thread O-ring boss

Remaining ports: SAE straight thread O-ring boss

Recommended installation position

Pump installation recommended with control position on the top or side. Consult Danfoss for non
conformance to these guidelines.
The housing must always be filled with hydraulic fluid.
Rear case drain recommended

Auxiliary cavity pressure

Will be equal to pump case pressure of rear housing.
Please verify mating pump shaft seal capability.

Physical Properties

Feature

Unit

Frame size

069

078

089

100

115

130

147

165

210

250

Displacem
ent

cm3 [in3]

69 [4.21]

78 [4.76]

89 [4.76]

100 [4.76]

115.2
[7.03]

130.0
[7.93]

147 [8.97]

165 [10.07] 211.5

[12.91]

251.7
[15.36]

Oil volume liter [US

gal]

2.0 [0.5]

3.0 [ 0.8]

7.2 [ 1.9]

Mounting flange

SAE flange, size C (SAE J 744) mounting pad

SAE flange, size D (SAE J 744) mounting pad

SAE flange, size E (ISO
3019-1 flange 177-4)
mounting pad

Auxiliary mounting

SAE A, SAE B, SAE B-B, SAE C

SAE A, SAE B, SAE B-B,
SAE C, SAE D

SAE A, SAE B, SAE B-B,
SAE C, SAE D, SAE E

Shafts

Splined:
21-teeth 16/32, 23-teeth 16/32, 14-teeth 12/24

Splined:
27-teeth 16/32,
13-teeth 8/16

Splined:
13-teeth 8/16
17-teeth 8/16,
27-teeth 16/32

Suction port

1.625-12UN-2B [1 5/8-12UN-2B]

Ø38 - 350 bar split
flange boss per ISO
6162 M12x1.75

Main port configuration Ø25.4 - 450 bar split flange boss per ISO 6162

M12x1.75

Ø31.5 - 450 bar split flange boss per ISO 6162
M12x1.75

Ø38 - 450 bar split
flange boss per ISO
6162 M16x2

Case drain ports L1, L3
(SAE O-ring boss).

Case drain ports L2, L4
(SAE O-ring boss)
prefered usage

0.875-12UNF-2B [7/8-12UNF-2B]

1.0625-12UNF-2B [1 1/16-12UNF-2B]

1.3175-12UNF-2B [1 5/16-12UNF-2B]

Port ISO 11926-1 - 1
5/16-12 (SAE O-ring
boss) only L2 and L4

Other ports

SAE O-ring boss. See installation drawings.

Customer interface
threads

Metric fastener

Service Manual

H1 Pumps 069/078, 089/100, 115/130, 147/165, 210/250

Technical Specifications

Danfoss | May 2018

520L0848 | AX00000087en-US0308 | 21

Summary of Contents for H1 069





































































Search results

Summary of Contents for H1 069

Reviews:

Related manuals for H1 069

Brands by name

Popular brands

Danfoss H1 069, Service Manual

Search results

Summary of Contents for H1 069

Reviews:

Related manuals for H1 069

Brands by name

Popular brands