Danfoss H1 069 Service Manual Download

Page: 50 / 68

Special Tool

Special

tool

Plug

P108 021E

Ø 1.7 mm (x3)

Ø 9.22 mm

45 deg.

Ø 14 mm

Inspection
Inspect machined surfaces on control and pump housing. Inspect plastic PC board housing and its
sealing areas. If any damage is found, replace damaged components.

Controls are available as a complete unit. Do not disassemble the control.

Assembly

1. If previously removed, install new screen (D084) in original orientation. Press in new retention ring

(D098).

Be sure screen will not move axially in bore after retention ring is installed.

Warning

Failure to install screen will result in erratic pump operation.

Proper Screen Orientation

P106 618E

D084

Incorrect screen
orientation

Correct screen
orientation

D094

2. If previously removed, use a 3 mm internal hex to install orifices (F00A, F00B) in original orientation.

Torque to 2.5 N•m [1.8 lbf•ft][.

3. Install new gasket (D150) to bottom of control.

If pump has been rebuilt or a new control is being installed, control software must be recalibrated.

Refer to H1-Automotive Control User Manual 70012797 for recalibration instructions.

Service Manual

H1 Pumps 069/078, 089/100, 115/130, 147/165, 210/250

Minor Repair

50 |

Danfoss | May 2018

520L0848 | AX00000087en-US0308

Summary of Contents for H1 069





































































Search results

Summary of Contents for H1 069

Reviews:

Related manuals for H1 069

Brands by name

Popular brands

Danfoss H1 069, Service Manual

Search results

Summary of Contents for H1 069

Reviews:

Related manuals for H1 069

Brands by name

Popular brands