Danfoss H1 069 Service Manual Download

Page: 48 / 68

4. Pull assembly fixture out before installing control screws.

Solenoid shaft

Feedback pin

Adjusting

screw

(cam)

Maximum

adjustment

less than 120°

Control spool

Remove plug (D065) and verify the swashplate feedback pin is properly positioned between control

feedback arms.

5. Using a 5 mm internal hex wrench, fasten control to pump with screws (D250). Torque screws to 13.5

N•m [10 lbf•ft] following torque sequence shown.

Torque sequence

(6 screw control)

D065

Warning

Calibration of sensor output in vehicle software is mandidtory after sensor replacement because

output signal can vary from one sensor to the next.

For proper neutral adjustment procedure, refer to

Automotive Control

Removal

1. Drain pump completely before removing control. Disconnect and remove wiring (D640).

Service Manual

H1 Pumps 069/078, 089/100, 115/130, 147/165, 210/250

Minor Repair

48 |

Danfoss | May 2018

520L0848 | AX00000087en-US0308

Summary of Contents for H1 069





































































Search results

Summary of Contents for H1 069

Reviews:

Related manuals for H1 069

Brands by name

Popular brands

Danfoss H1 069, Service Manual

Search results

Summary of Contents for H1 069

Reviews:

Related manuals for H1 069

Brands by name

Popular brands