Danfoss H1 069 Service Manual Download

Page: 56 / 68

7. Remove valve plate (S250) with seal (S300). Note orientation of valve plate and seal. Discard seal

(S300).

Charge Pump Removal/Installation

P106 036E

K100

K150

K500

G450

S150

S300

S250

S100

S300

S200

K200

K100

K400
10 mm
92 Nm [68 ft•lb]

Charge Pump Removal (integrated auxiliary pad)

1. Remove auxilliary pump and O-ring (K250). Discard O-ring.
2. Remove charge pump cover screws (K450) and charge pump cover (K550).
3. Remove thrust washer (K500). Note its orientation. Coated side is towards charge pump coupling

(K200).

4. Remove pressure-balance plate (S200) with seal (S300). Note orientation of valve plate and seal.

Discard seal (S300).

5. Remove charge pump coupling K200).
6. Remove charge pump gearset (S100) and outer ring (S150).

Service Manual

H1 Pumps 069/078, 089/100, 115/130, 147/165, 210/250

Minor Repair

56 |

Danfoss | May 2018

520L0848 | AX00000087en-US0308

Summary of Contents for H1 069





































































Search results

Summary of Contents for H1 069

Reviews:

Related manuals for H1 069

Brands by name

Popular brands

Danfoss H1 069, Service Manual

Search results

Summary of Contents for H1 069

Reviews:

Related manuals for H1 069

Brands by name

Popular brands