Carrier Gemini 38AU07 Series Installation Instructions Manual Download

Page: 1 / 52

Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.

Catalog No. 04-53380020-01

Printed in U.S.A.

Form 38AU-7-14-03SI

Pg 1

1-19

Replaces: 38AU-7-14-02SI

Installation Instructions

CONTENTS

Page

SAFETY CONSIDERATIONS

. . . . . . . . . . . . . . . . . . . . . . 1

INSTALLATION GUIDELINES

. . . . . . . . . . . . . . . . . . . . . 2

Replacement/Retrofit — R-22 to Puron

. . . . . . . . . . . 2

Rated Indoor Airflow (cfm)

. . . . . . . . . . . . . . . . . . . . . . . 3

Identify Factory Options

. . . . . . . . . . . . . . . . . . . . . . . . . 3

Matching 38AU Model to Evaporator Coil

. . . . . . . . 3

General

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

INSTALLATION

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Jobsite Survey

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Step 1 — Plan for Unit Location

. . . . . . . . . . . . . . . . . . 6

Step 2 — Complete Pre-Installation Checks

. . . . . . 7

Step 3 — Prepare Unit Mounting Support

. . . . . . . . 7

Step 4 — Rig and Mount the Unit

. . . . . . . . . . . . . . . . . 7

Step 5 — Determine Refrigerant Line Sizes

. . . . . . 7

Suction Riser

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Step 6 — Complete Refrigerant Piping

Connections

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Step 7 — Install Accessories

. . . . . . . . . . . . . . . . . . . . 14

Step 8 — Complete Electrical Connections

. . . . . . 14

Step 9 — Wind Baffles for Low Ambient

Control

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

PRE-START-UP

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

System Check

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Turn on Crankcase Heater

. . . . . . . . . . . . . . . . . . . . . . 23

Preliminary Charge

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

START-UP

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Preliminary Checks

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Start Unit

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

OPERATING SEQUENCE

. . . . . . . . . . . . . . . . . . . . . . . . 32

Base Unit Controls

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

38AUDC with SVR Relays

. . . . . . . . . . . . . . . . . . . . . . . 33

All Units

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

MAINTENANCE

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Quarterly Inspection (and 30 Days After

Initial Start)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Seasonal Maintenance

. . . . . . . . . . . . . . . . . . . . . . . . . . 34

SERVICE

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Refrigeration System

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Comfort Alert Diagnostic Module

. . . . . . . . . . . . . . . 36

Compressor Protection

. . . . . . . . . . . . . . . . . . . . . . . . . 38

Fastener Torque Values

. . . . . . . . . . . . . . . . . . . . . . . . . 39

TROUBLESHOOTING

. . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Appendix A — Air Conditioner and Heat Pump

with Puron® Quick Reference Guide

. . . . . . . . . 41

Appendix B — Wiring Diagram List

. . . . . . . . . . . . . 42

Appendix B — Low Ambient-Option,

Factory Installed

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

START-UP CHECKLIST

. . . . . . . . . . . . . . . . . . . . . . CL-1

SAFETY CONSIDERATIONS

Improper installation, adjustment, alteration, service, main-

tenance, or use can cause explosion, fire, electrical shock or

other conditions which may cause personal injury or property

damage. Consult a qualified installer, service agency, or your

distributor or branch for information or assistance. The quali-

fied installer or agency must use factory-authorized kits or ac-

cessories when modifying this product. Refer to the individual

instructions packaged with the kits or accessories when

installing.

Follow all safety codes. Wear safety glasses and work

gloves. Use quenching cloths for brazing operations and have a

fire extinguisher available. Read these instructions thoroughly

and follow all warnings or cautions attached to the unit. Con-

sult local building codes and appropriate national electrical

codes (in USA, ANSI/NFPA 70, National Electrical Code

(NEC); in Canada, CSA C22.1) for special requirements.

It is important to recognize safety information. This is the

safety-alert symbol

. When you see this symbol on the unit

and in instructions or manuals, be alert to the potential for per-

sonal injury.

Understand the signal words DANGER, WARNING, CAU-

TION, and NOTE. These words are used with the safety-alert

symbol. DANGER identifies the most serious hazards which

will

result in severe personal injury or death. WARNING signi-

fies hazards which

could

result in personal injury or death.

CAUTION is used to identify unsafe practices, which

may

re-

sult in minor personal injury or product and property damage.

NOTE is used to highlight suggestions which

will

result in en-

hanced installation, reliability, or operation.

WARNING

FIRE, EXPLOSION HAZARD
Failure to follow this warning could result in personal

injury or death.
Disconnect gas piping from unit when leak testing at pres-

sure greater than 0.5 psig (3450 Pa). Pressures greater than

0.5 psig (3450 Pa) will cause gas valve damage resulting in

hazardous condition. If gas valve is subjected to pressure

greater than 0.5 psig (3450 Pa), it must be replaced before

use. When pressure testing field-supplied gas piping at

pressures of 0.5 psig (3450 Pa) or less, a unit connected to

such piping must be isolated by closing the manual gas

valve.

WARNING

ELECTRICAL SHOCK HAZARD
Failure to follow this warning could cause personal injury

or death.
Before performing service or maintenance operations on

unit, always turn off main power switch to unit and install

lock(s) and lockout tag(s). Unit may have more than one

power switch.

Gemini™

38AU07-14

Air-Cooled Condensing Units

with Puron

(R-410A) Refrigerant

Summary of Contents for Gemini 38AU07 Series





















































Search results

Summary of Contents for Gemini 38AU07 Series

Reviews:

Related manuals for Gemini 38AU07 Series

Brands by name

Popular brands

Carrier Gemini 38AU07 Series, Installation Instructions Manual

Search results

Summary of Contents for Gemini 38AU07 Series

Reviews:

Related manuals for Gemini 38AU07 Series

Brands by name

Popular brands