Carrier Gemini 38AU07 Series Installation Instructions Manual Download Page 6

Page: 6 / 52

Table 5 — 38AU Corner Weights

Table 6 — 38AU**07-14 Physical Data

Approximate system charge with about 25 ft piping of sizes indi-

cated with matched 40RU.

INSTALLATION

Jobsite Survey

Complete the following checks before installation.

1. Consult local building codes and the NEC (National

Electrical Code) ANSI/NFPA 70 for special installation
requirements.

2. Determine unit location (from project plans) or select

unit location.

3. Check for possible overhead obstructions which may

interfere with unit lifting or rigging.

Step 1 — Plan for Unit Location

The 38AU units are designed and approved for outdoor in-

stallation only. Do not locate these units indoors. Do not add

ducting to unit fan system.

Select a location for the unit and its support system (pad,

rails or other) that provides for the minimum clearances re-

quired for safety. This includes the clearance to combustible

surfaces, unit performance and service access below, around

and above unit as specified in unit drawings. See Fig. 4.
NOTE: Local codes may require different clearances than

specified in Fig. 4. It is the responsibility of installers to be

knowledgeable in local codes and to modify the recommend-

ed clearances to satisfy local codes.
NOTE: Consider also the effect of adjacent units on airflow per-

formance and control box safety clearance.

UNIT

STD. UNIT

WT.

CORNER A

CORNER B

CORNER C

CORNER D

CENTER OF GRAVITY

UNIT

HEIGHT

lbs.

kg.

lbs.

kg.

lbs.

kg.

lbs.

kg.

lbs.

kg.

38AUZ*07 (RTPF)

389

176

141

[457.2]

[609.6]

[533.4]

42 3/8

[1076.0]

38AUZ*08

(RTPF)

391

177

142

[457.2]

[609.6]

[533.4]

42 3/8

[1076.0]

38AUZ*12 (RTPF)

490

222

177

120

114

[457.2]

[609.6]

50 3/8

[1279.2]

38AUZ*14

(RTPF)

598

271

195

142

110

151

[508.0]

[635.0]

[609.6]

50 3/8

[1279.2]

38AUD*12

(RTPF)

516

234

185

117

131

[482.6]

[584.2]

[609.6]

50 3/8

[1279.2]

38AUD*14

(RTPF)

654

297

214

155

120

165

[508.0]

[635.0]

[609.6]

50 3/8

[1279.2]

SINGLE CIRCUIT MODELS with RTPF – ROUND TUBE/PLATE FIN COIL DESIGN

38AUZ(A,B)07

38AUZ(D,E)07

38AUZ(A,B)08

38AUZ(D,E)08

38AUZ12

38AUZ14

Refrigeration System

# Circuits / # Comp. / Type

1 / 1 / Scroll

Refrigerant Type

Puron® R-410A

R-410A shipping charge A/B (lbs, 60 Hz)

9.0

System charge w/ fan coil* (60 Hz)

14.0

17.0

19.0

20.0

43.0

R-410A shipping charge A/B (lbs, 50 Hz)

9.0

N/A

System charge w/ fan coil* (50 Hz)

14.0

17.0

N/A

Metering device

TXV

High-press. Trip / Reset (psig)

630 / 505

Low-press. Trip / Reset (psig)

54 / 117

Compressor

Model

ZP61

ZPS60

ZP83

ZPS83

ZP104

ZP137

Oil Charge A/B (oz)

110

Speed (rpm, 60/50 Hz)

3500 / 2900

3500

Condenser Coil

Material

Al/Cu

Coil type

RTPF

Rows / FPI

2 / 17

3 / 17

total face area (ft

)

17.5

23.0

25.1

31.8

Condenser fan / motor

Qty / Motor drive type

2 / direct

Motor HP / RPM

/ 1100

Fan diameter (in.)

Nominal Airflow (cfm)

6,000

Watts (total)

610

Piping Connections

Qty / Suction (in. ODS)

1 / 1

Qty / Liquid (in. ODS)

1 /

Summary of Contents for Gemini 38AU07 Series





















































Search results

Summary of Contents for Gemini 38AU07 Series

Reviews:

Carrier Gemini 38AU07 Series, Installation Instructions Manual, Page: 6 / 52

Search results

Summary of Contents for Gemini 38AU07 Series

Reviews: