background image

Electric machine installation checklist

Date:

Electric machine and customer information 

Customer:

Electric machine type (from the rating plate):

Customer reference:

Electric machine serial number:

Service reference:

Date installed:

N.A = Procedure not applicable PASS = Procedure passed FAIL = Procedure failed

Installation checklist

Approval

N.A

PASS

FAIL

General
Electric machine type is correct

Electric machine is
undamaged

Insulation resistance check
(Reference value of 150 MΩ
should not be exceeded at
reference ambient
temperature 25°C (measured
with 500 V

DC

 / 1 min

Megger))

>150MΩ

Environmental conditions as
specified (see data sheet)

Mechanical installation
Supporting structure as required

Shaft alignment as specified (see chapter Shaft alignment
and load). 

D-end attachment bolt
tightening torque

40 Nm

N-end attachment bolt
tightening torque

30 Nm

Cooling circuit connected
and coolant flowing

Used coolant:

Power connections
Cable gland assembly as specified (cable gland to cables)
with correct cable diameter

Cable lug air cap (to metallic
structures)

≥10 mm

Cable gland tightening
torque (to the box)

15 Nm

Cable lug tightening torque
(to the busbar)

13 Nm

The phase connections order is correct (U, V, W -> L1, L2,
L3)

Connection box cover bolts
tightening torque

4 Nm

User Guide

EM-PMI375

Storage, installation and maintenance checklists

 

©

 Danfoss | November 2021

BC265856307805en-000202 | 77

Summary of Contents for EM-PMI375




















































































Reviews: