manualshive.com logo in svg

Danfoss EM-PMI375, User Manual

Share
Download
Danfoss EM-PMI375 User Manual Download Page 67

Make sure that the mating structure is not damaged. Do not pluck any bores or use at headed

bolts or rods for pushing the electric machine out of the mating structure.

For dismounting the electric machine, follow the Steps below.

See Chapter 

Mounting the electric machine

 on page 38. Dismount the electric machine in reverse order.

1. Prepare the electric machine for lifting, for more information refer to Chapter 

Lifting

 on page 31.

Support the electric machine with lifting slings when dismounting.

2. Loosen the mounting bolts. For more information refer to Chapter 

Mounting the electric machine

 on

page 38.

3. If force is required, use the bores in D-end flange to push the electric machine out from the mating

structure, or use some other method that does not damage the electric machine.

4. Lift the electric machine off. Support the electric machine when lifting.

User Guide

EM-PMI375

Dismounting

 

©

 Danfoss | November 2021

BC265856307805en-000202 | 67

Summary of Contents for EM-PMI375




















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands