manualshive.com logo in svg

Danfoss EM-PMI375, User Manual

Share
Download
Danfoss EM-PMI375 User Manual Download Page 50

The electric machine has a connector or a connection box which is used to read out in-built temperature
and rotation sensor (resolver) data from the electric machine. The temperature data comes from PT100
sensors in the stator windings and in some cases in the bearings. The rating plate has the information
about the options of the electric machine: different options add sensors, and some electric machines do
not have all the sensors. For more information about the options, refer to Chapter 

Product naming

convention 

 on page 5. 

Recommended cable types for low voltage connections

Application

Cable type

Resolver cabling

Shielded cable (twisted pair)

Temperature measurement (PT100)

Shielded cable (twisted pair)

Low voltage connector (1), Deutsch HD34-24-47PE

Low voltage connection box (+LVB1 -option)

User Guide

EM-PMI375

Installation

 

50 | 

©

 Danfoss | November 2021

BC265856307805en-000202

Summary of Contents for EM-PMI375




















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands