D&H DH05C Manual Download Page 77 | Manualshive

Page: 77 / 106

background image

77

Fahrzeug-/Funktionsdecoder

ab Firmware-Version 1.11

77

Locomotive/Vehicle function decoder

from firmware version 3.12

•  Enter now the hundredth and ten‘s digit of the new CV value.
  Example: Value 135 is to be written: Enter ‘13‘.
•  Activate the reversion of the driving direction for confirmation. The lighting flashes long - short - short – short
(periodically)
•  Enter now the unit place of the new CV in double digit. Example: Enter ‘05‘.
•  Activate the reversion of the driving direction for confirmation.
  Then the locomotive is flashing again.
•  You may now enter further CVs in long mode which you want to change

The long mode can be left by switching the track voltage off and on again or by STOP.

SUSI mode

You gain the SUSI mode by writing value 09 in CV09 in short mode.
The decoder confirms that by slow flashing.

Enter CVs respective the related values as in long mode and reduce all CVs about 900.
Thus changes CV903 to 003 for example.
Notice please that you are operating in SUSI mode, which is programmed according to the long mode.

Notice:
It is easier to do the programming under DCC.
Thus programmed values are also valid for MM format.

«
...
75
76
77
78
79
...
»

Summary of Contents for DH05C











































































































Reviews:

No comments

Related manuals for DH05C

Brand: Panasonic Pages: 155

SiriusXM CQ-RXBT490U

Brand: Panasonic Pages: 6

Brand: Cambridge Audio Pages: 4

Brand: Cambridge Audio Pages: 2

Brand: C&C TECHNIC Pages: 2

Brand: Kramer Pages: 14

Brand: Potek Pages: 18

Brand: Cerwin-Vega Pages: 12

Z3-SBE264-DVR-13

Brand: Z3 Technology Pages: 50

Brand: CYP Pages: 12

Brand: YASKAWA Pages: 67

Brand: LAN Power Pages: 2

Brand: Aquatic Pages: 5

Brand: ELGO Electronic Pages: 40

LOUDSPEAKER SP100

Brand: Sonos Pages: 46

Brand: American Audio Pages: 40

Brand: Sennheiser Pages: 2

Brand: Zling Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands