manualshive.com logo in svg

D&H DH05C, Manual, Page: 100 / 106

Share
Download
D&H DH05C Manual Download Page 100

100

Fahrzeug-/Funktionsdecoder

 ab Firmware-Version 1.11

100

Locomotive/Vehicle function decoder

 from firmware version 3.12

Operating the couplings with 2 function keys

Should the couplings be connected for example to AUX3 (in front) and AUX4 (at the rear), times are to be entered at AUX3 
and AUX4. The mapping of the function keys (which function key should control which coupling), is set by the normale 
function mapping (see next page).

For example F3 = AUX3 and F4 = AUX4 should be assigned:
CV37  Function mapping F3 (in the example = 16 for AUX3)
CV38  Function mapping F4 (in the example = 32 for AUX4)

Operating the couplings with 1 function key

Should the couplings be connected for example to AUX3 (in front) and AUX4 (at the rear), times are to be entered at AUX3 
and AUX4. The corresponding function key must now be assigned to both couplings.

For example shall F4 = AUX3 and AUX4 operate:
CV38  Function mapping F4 (in example = 16 + 32 = 48 for AUX3 + AUX4)

Which coupling should react must be defined by a condition.
In the example AUX3 should that be for forward and AUX4 for backward:
CV149  Condition for AUX3: forward only = 1
CV150  Condition for AUX4: backward only = 2

Summary of Contents for DH05C











































































































Reviews:

No comments